Dell PowerEdge R250 EMC Installation and Service Manual - Page 78

Installing the left control panel, Removing the right control panel, Prerequisites, Steps, Next steps

Get Dell PowerEdge R250 PDF manuals and user guides View all Dell PowerEdge R250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Installing the left control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the front bezel. 4. Remove the air shroud. Steps 1. Route the control panel cable through the side and the guide slots in the system. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 2. Align and insert the left control panel assembly in the slot on the system. 3. Connect the control panel cable to the system board connector. 4. Using the Phillips #1 screwdriver, tighten the screws that secure the left control panel assembly to the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Figure 75. Installing the left control panel Next steps 1. Replace the air shroud. 2. Replace front bezel. 3. Follow the procedure listed in the After working inside your system. Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 78 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Installing the left control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the front bezel
.
4.
Remove the air shroud
.
Steps
1.
Route the control panel cable through the side and the guide slots in the system.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
2.
Align and insert the left control panel assembly in the slot on the system.
3.
Connect the control panel cable to the system board connector.
4.
Using the Phillips #1 screwdriver, tighten the screws that secure the left control panel assembly to the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 75. Installing the left control panel
Next steps
1.
Replace the air shroud
.
2.
Replace front bezel
.
3.
Follow the procedure listed in the
After working inside your system
.
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
78
Installing and removing system components