Dell S5148F-ON OS10 Enterprise Edition User Guide Release 10.3.2E-R1 - Page 520
Password recovery, xe-7-0-1.XL3.SJC7.ALTER.NET 152.63.48.254
View all Dell S5148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 520 highlights
• -t tos - (Optional) For IPv4, enter the Type of Service (TOS) and Precedence values to use. 16 sets a low delay; 8 sets a high throughput. • -UL - (Optional) Use UDPLITE for tracerouting (default port is 53). • -w waittime - (Optional) Enter the time (in seconds) to wait for a response to a probe (default 5 seconds). • -z sendwait - (Optional) Enter the minimal time interval to wait between probes (default 0). A value greater than 10 specifies a number in milliseconds, otherwise it specifies a number of seconds. This option is useful when routers rate-limit ICMP messages. • --mtu - (Optional) Discovers the MTU from the path being traced. • --back - (Optional) Prints the number of backward hops when it seems different with the forward direction. • host - (Required) Enter the name or IP address of the destination device. • packet_len - (Optional) Enter the total size of the probing packet (default 60 bytes for IPv4 and 80 for IPv6). Default Command Mode Usage Information Example Not configured EXEC None OS10# traceroute www.dell.com traceroute to www.dell.com (23.73.112.54), 30 hops max, 60 byte packets 1 10.11.97.254 (10.11.97.254) 4.298 ms 4.417 ms 4.398 ms 2 10.11.3.254 (10.11.3.254) 2.121 ms 2.326 ms 2.550 ms 3 10.11.27.254 (10.11.27.254) 2.233 ms 2.207 ms 2.391 ms 4 Host65.hbms.com (63.80.56.65) 3.583 ms 3.776 ms 3.757 ms 5 host33.30.198.65 (65.198.30.33) 3.758 ms 4.286 ms 4.221 ms 6 3.GigabitEthernet3-3.GW3.SCL2.ALTER.NET (152.179.99.173) 4.428 ms 2.593 ms 3.243 ms 7 0.xe-7-0-1.XL3.SJC7.ALTER.NET (152.63.48.254) 3.915 ms 3.603 ms 3.790 ms 8 TenGigE0-4-0-5.GW6.SJC7.ALTER.NET (152.63.49.254) 11.781 ms 10.600 ms 9.402 ms 9 23.73.112.54 (23.73.112.54) 3.606 ms 3.542 ms 3.773 ms Example (IPv6) OS10# traceroute 20::1 traceroute to 20::1 (20::1), 30 hops max, 80 byte packets 1 20::1 (20::1) 2.622 ms 2.649 ms 2.964 ms Supported Releases 10.2.0E or later Password recovery You may need to recovery your lost password. 1 Connect to the serial console port. The serial settings are 115200 baud, 8 data bits, and no parity. 2 Reboot or power up the system. 3 Press ESC at the Grub prompt to view the boot menu. The OS10-A partition is selected by default. |*OS10-A | | OS10-B | | ONIE | 4 Press e to open the OS10 GRUB editor. 5 Use the arrow keys to highlight the line that starts with linux. Add init=bin/bash at the end of the line. |setparams 'OS10-A' | 520 Troubleshoot OS10