HP Integrity rx2800 Installation Guide - Page 55

Powering On the Server, Powering On the Server Using the iLO 3 MP

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

NOTE: If the power restore feature is set to Always On through the iLO 3 MP PR command, the server automatically powers on to the full power state when the power cord is plugged in to the server. Powering On the Server Power on the server to full power using the following methods if the server is in the standby power state: • iLO 3 MP PC command • Power button Powering On the Server Using the iLO 3 MP NOTE: If the power restore feature is set to Always On through the iLO 3 MP PR command, the server automatically powers on to the full power state when the power cord is plugged in to the server. To power on the server using the iLO 3 MP, follow these steps: 1. Plug all power cables into the receptacles on the rear panel of the server. 2. Initiate a console session, and access the MP Main Menu. 3. Enter CM to enable command mode. 4. Enter PC to use the remote power control command. 5. Enter ON to power on the server, and enter YES when prompted to confirm the action. 6. Start the operating system. For more information, see the operating system documentation. Powering On the Server Manually NOTE: If the power restore feature is set to Always On through the iLO 3 MP PR command, the server automatically powers on to the full power state when the power cord is plugged in to the server. To manually power on the server, follow these steps: 1. Plug all power cables into the receptacles on the rear panel of the server. 2. Press the power button to start the server. 3. Start the operating system. For more information, see the operating system documentation.) Powering Off the Server Power off the server using the following methods if the server is in the standby or full power state: • iLO 3 MP PC command • Power button Powering Off the Server Using the iLO 3 MP To power off the server using the iLO 3 MP, follow these steps: 1. Gracefully shut down the operating system. See the operating system documentation for more information. 2. Initiate a console session, and access the MP Main Menu. 3. Enter CM to enable command mode. 4. Enter PC to use the remote power control command. Powering On and Powering Off the Server 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
NOTE:
If the power restore feature is set to
Always On
through the iLO 3 MP
PR
command,
the server automatically powers on to the full power state when the power cord is plugged in
to the server.
Powering On the Server
Power on the server to full power using the following methods if the server is in the standby
power state:
•
iLO 3 MP
PC
command
•
Power button
Powering On the Server Using the iLO 3 MP
NOTE:
If the power restore feature is set to
Always On
through the iLO 3 MP
PR
command,
the server automatically powers on to the full power state when the power cord is plugged in
to the server.
To power on the server using the iLO 3 MP, follow these steps:
1.
Plug all power cables into the receptacles on the rear panel of the server.
2.
Initiate a console session, and access the
MP Main Menu
.
3.
Enter
CM
to enable command mode.
4.
Enter
PC
to use the remote power control command.
5.
Enter
ON
to power on the server, and enter
YES
when prompted to confirm the action.
6.
Start the operating system. For more information, see the operating system documentation.
Powering On the Server Manually
NOTE:
If the power restore feature is set to
Always On
through the iLO 3 MP
PR
command,
the server automatically powers on to the full power state when the power cord is plugged in
to the server.
To manually power on the server, follow these steps:
1.
Plug all power cables into the receptacles on the rear panel of the server.
2.
Press the power button to start the server.
3.
Start the operating system. For more information, see the operating system documentation.)
Powering Off the Server
Power off the server using the following methods if the server is in the standby or full power
state:
•
iLO 3 MP
PC
command
•
Power button
Powering Off the Server Using the iLO 3 MP
To power off the server using the iLO 3 MP, follow these steps:
1.
Gracefully shut down the operating system. See the operating system documentation for
more information.
2.
Initiate a console session, and access the
MP Main Menu
.
3.
Enter
CM
to enable command mode.
4.
Enter
PC
to use the remote power control command.
Powering On and Powering Off the Server
55