HP MSA2324sa HP StorageWorks 2300 Family Modular Smart Array CLI reference gui - Page 98

set host-parameters, Optional. For iSCSI, the port netmask address in IPv4 format.

Get HP MSA2324sa PDF manuals and user guides View all HP MSA2324sa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

set host-parameters Description Sets controller host port parameters for communication with attached hosts. The new settings take effect without restarting the controllers. There are parameters for FC and iSCSI ports but not for SAS ports. Syntax set host-parameters [controller a|b|both] [speed 1g|2g|4g|auto] [ports #|all] [fibre-connection-mode loop|point-to-point] [ip address] [netmask address] [gateway address] [prompt yes|no|y|n|expert] [noprompt] [fibre-loop-id values] Parameters controller a|b|both Optional. Specifies whether to apply the settings to all host ports in controller A, B, or both. speed 1g|2g|4g|auto Optional. Sets a forced link speed in Gbit/sec or lets the speed be auto-negotiated (auto). ports #|all Optional. Specific host port numbers or all ports. For syntax, see Command syntax. If this parameter is omitted, all host ports on the specified controllers are affected. fibre-connection-mode loop|point-to-point Optional. For FC, sets the topology for the specified ports to either: • loop: Fibre Channel-Arbitrated Loop (public or private) • point-to-point: Fibre Channel point-to-point. You must also specify the controller parameter. ip address Optional. For iSCSI, the port IP address in IPv4 format. netmask address Optional. For iSCSI, the port netmask address in IPv4 format. gateway address Optional. For iSCSI, the port gateway address in IPv4 format. prompt yes|no|y|n|expert Deprecated; use the noprompt parameter instead. noprompt Optional. Specifies an automatic response to the confirmation prompt that enables the operation to proceed. If this parameter is omitted, you must reply to the prompt. 98

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
98
set host-parameters
Description
Sets controller host port parameters for communication with attached hosts. The new settings take
effect without restarting the controllers. There are parameters for FC and iSCSI ports but not for SAS
ports.
Syntax
set host-parameters
[controller a|b|both]
[speed 1g|2g|4g|auto]
[ports
#
|all]
[fibre-connection-mode loop|point-to-point]
[ip
address
]
[netmask
address
]
[gateway
address
]
[prompt yes|no|y|n|expert]
[noprompt]
[fibre-loop-id
values
]
Parameters
controller a|b|both
Optional. Specifies whether to apply the settings to all host ports in controller A, B, or both.
speed 1g|2g|4g|auto
Optional. Sets a forced link speed in Gbit/sec or lets the speed be auto-negotiated (
auto
).
ports
#
|all
Optional. Specific host port numbers or all ports. For syntax, see
Command syntax
. If this parameter
is omitted, all host ports on the specified controllers are affected.
fibre-connection-mode loop|point-to-point
Optional. For FC, sets the topology for the specified ports to either:
•
loop
: Fibre Channel-Arbitrated Loop (public or private)
•
point-to-point
: Fibre Channel point-to-point.
You must also specify the
controller
parameter.
ip
address
Optional. For iSCSI, the port IP address in IPv4 format.
netmask
address
Optional. For iSCSI, the port netmask address in IPv4 format.
gateway
address
Optional. For iSCSI, the port gateway address in IPv4 format.
prompt yes|no|y|n|expert
Deprecated; use the
noprompt
parameter instead.
noprompt
Optional. Specifies an automatic response to the confirmation prompt that enables the operation to
proceed. If this parameter is omitted, you must reply to the prompt.