Home » IBM Manuals » Desktops » IBM 86655RY » Manual Viewer

IBM 86655RY Hardware Maintenance Manual - Page 184

CRTxxx was found on Controller 2 A2, Channel 3 C3, SCSI ID 4 SID04.

Add to My Manuals
Save this manual to your list of manuals

Page 184 highlights

To run the IPSMON program: 1. From the console, type: load ipsmon 2. Press Enter. When you start IPSMON, it immediately begins polling all ServeRAID controllers for specific conditions. If a condition being monitored is found, this program logs a message to the screen, to a file, or to both the screen and a file. Note: IPSMON continuously polls the ServeRAID controllers until you type unload ipsmon at the system console. Supported operating systems: NetWare Command: ipsmon options where: • options is one of the following optional parameters: - -F:filename to specify the name of the file in which to record messages. The default file name is IPSMON.LOG. - -S to display messages on the standard output (usually the monitor) - -? to obtain a current list of valid parameters Note: If you start this program without any command-line parameters, the IPSMON program will log the messages to the IPSMON.LOG file, and the messages will not appear on the screen. During operation, IPSMON logs various messages. Each message contains an alert code and a location specifier. • The alert code begins with the message type and number; for example, INF, WRN, or CRT (followed by the message number). • The location specifier comes after the alert code: A followed by the controller number SID followed by the SCSI ID (if required) C followed by the channel number (if required) For example, a message of CRTxxx:A2C3SID04 signifies that a Critical condition (CRTxxx) was found on Controller 2 (A2), Channel 3 (C3), SCSI ID 4 (SID04). The IPSMON program can log the following messages, based on the required condition. Information Messages: INF000:A1C-SID-- no errors detected INF001:A1C-SID-- rebuild started INF002:A1C-SID-- rebuild completed INF003:A1C-SID-- synchronization started INF004:A1C-SID-- synchronization completed INF005:A1C-SID-- migration started INF006:A1C-SID-- migration completed Warning Messages: WRN001:A2C3SID12 PFA Error detected Critical Messages: CRT001:A3C2SID04 dead drive detected CRT002:A1C-SID-- not responding to commands 174 Hardware Maintenance Manual: Netfinity 7600 - Type 8665 Models 1RY, 2RY

Section	Page
About this manual	5
Important safety information	5
Online support	6
General checkout	11
General information	13
Features and specifications	13
Server features	15
Reliability, availability, and serviceability	16
Controls and indicators	17
Information LED panel	19
Diagnostics	21
Diagnostic tools overview	21
POST	22
Small computer system interface messages	22
Solving ServeRAID problems	23
Diagnostic programs and error messages	34
Light path diagnostics	37
Power checkout	41
Temperature checkout	41
Recovering BIOS	42
Replacing the battery	42
Diagnosing errors	44
Configuring the server	53
Using the Configuration/Setup Utility program	53
Using the SCSISelect utility program	59
Installing options	63
Major components of the Netfinity 7600	63
Component locations	64
Before you begin	70
Removing the server top cover and bezel	71
Working with adapters	73
Installing internal drives	76
Installing memory-module kits	81
Installing a microprocessor kit	83
Installing a hot-swap power supply	86
Replacing a hot-swap fan	88
Completing the installation	89
Connecting external options	91
Input/output ports	91
Cabling the server	103
Installing the server in a rack	103
Netfinity Manager	105
Managing your IBM Netfinity server with Netfinity Manager	106
Netfinity Manager documentation	106
Netfinity Manager system requirements	106
Starting the Netfinity Manager installation program	108
Netfinity Manager database support	115
Starting Netfinity Manager	125
Getting more information about Netfinity Manager	132
Installation options	133
FRU information (service only)	137
Diagnostic switch card	137
Disconnecting the shuttle	138
Front LED card assembly	138
I/O Legacy board	139
Memory card removal	140
PCI switch card	142
Power backplane assembly	142
Processor/PCI backplane	143
Removing the shuttle	145
SCSI backplane assembly	145
SCSI daughter card	146
Installing and configuring ServeRAID controllers	149
Features and connector locations of ServeRAID-4H controller	149
Features and connector locations of ServeRAID-4L controller	151
Features and connector locations of ServeRAID-4M controller	153
Using a ServeRAID-4x controller in a server with Hot-plug PCI features	155
Step 1: Installing and cabling a ServeRAID controller	156
Step 2: Updating BIOS and firmware code	161
Step 3: Configuring ServeRAID controllers	161
Obtaining ServeRAID updates	172
ServeRAID device driver order on Windows 2000 and Windows NT 4.0	174
Using utility programs	175
Introduction to IBM ServeRAID cluster solution	185
Monitoring and updating an IBM ServeRAID cluster solution	186
POST (ISPR) error codes and procedures	190
Recovery procedures for defunct (DDD) drives	194
Channel record table	201
Reference information	202
Symptom-to-FRU index	225
Beep symptoms	225
No beep symptoms	228
Diagnostic panel LEDs	228
Diagnostic error codes	230
Error symptoms	235
Power supply LED errors	235
POST error codes	236
ServeRAID POST (ISPR) error codes	242
ServeRAID	244
SCSI error codes	246
Temperature error messages	246
Fan error messages	247
Power error messages	247
System shutdown	248
DASD checkout	249
Host Built-In Self Test (BIST) checkout	249
I2C bus fault messages	249
Undetermined problems	251
Parts listing (Type 8665)	253
Part A	253
Part B	254
System	255
Keyboards	256
Power cords	257
Related service information	259
Safety information	259
Send us your comments!	289
Problem determination tips	290
Notices	290

Match case Limit results 1 per page

174

Hardware Maintenance Manual: Netfinity 7600

–

Type 8665 Models 1RY, 2RY

To run the IPSMON program:

From the console, type:

load ipsmon

Press Enter.

When you start IPSMON, it immediately begins polling all ServeRAID controllers for

specific conditions.

If a condition being monitored is found, this program logs a

message to the screen, to a file, or to both the screen and a file.

Note:

IPSMON continuously polls the ServeRAID controllers until you type

unload

ipsmon

at the system console.

Supported operating systems: NetWare

Command:

ipsmon

options

where:

•

options

is one of the following optional parameters:

—

-F:

filename

to specify the name of the file in which to record messages. The

default file name is IPSMON.LOG.

—

-S to display messages on the standard output (usually the monitor)

—

-? to obtain a current list of valid parameters

Note:

If you start this program without any command-line parameters, the

IPSMON program will log the messages to the IPSMON.LOG file, and the

messages will not appear on the screen.

During operation, IPSMON logs various messages. Each message contains an alert

code and a location specifier.

•

The alert code begins with the message type and number; for example, INF,

WRN, or CRT (followed by the message number).

•

The location specifier comes after the alert code:

followed by the controller number

SID

followed by the SCSI ID (if required)

followed by the channel number (if required)

For example, a message of

CRTxxx:A2C3SID04

signifies that a Critical condition

(CRTxxx) was found on Controller 2 (A2), Channel 3 (C3), SCSI ID 4 (SID04).

The IPSMON program can log the following messages, based on the required

condition.

Information Messages:

INF000:A1C-SID-- no errors detected

INF001:A1C-SID-- rebuild started

INF002:A1C-SID-- rebuild completed

INF003:A1C-SID-- synchronization started

INF004:A1C-SID-- synchronization completed

INF005:A1C-SID-- migration started

INF006:A1C-SID-- migration completed

Warning Messages:

WRN001:A2C3SID12 PFA Error detected

Critical Messages:

CRT001:A3C2SID04

dead drive detected

CRT002:A1C-SID--

not responding to commands