Home » IBM Manuals » Desktops » IBM 86655RY » Manual Viewer

IBM 86655RY Hardware Maintenance Manual - Page 232

Fixed Disk with SCSI ID NN on RAID adapter in PCI slot S., VRM for Optional Microprocessor 3

Add to My Manuals
Save this manual to your list of manuals

Page 232 highlights

Error Code/Symptom FRU/Action 035-XXX-SNN (Check System Error 1. Fixed Disk with SCSI ID NN on RAID adapter in PCI slot S. Log before replacing a FRU. S = number of failing PCI slot; NN = SCSI ID of failing fixed disk.) 035-253-S99 (RAID adapter initialization failure) 1. ServeRAID Adapter in slot S is not configured properly. Obtain the basic and extended configuration status and refer to the ServeRAID Hardware Maintenance Manual for more information. 2. Cable 3. SCSI Backplane 4. Adapter 075-XXX-000 test) (Failed Power Supply 1. Power Supply 089-XXX-001 test) (Failed Microprocessor 1. VRM for Microprocessor 1 2. Microprocessor 089-XXX-002 (Failed Optional Microprocessor test) 1. VRM for Optional Microprocessor 2 2. Optional Microprocessor 089-XXX-003 (Failed Optional Microprocessor test) 1. VRM for Optional Microprocessor 3 2. Optional Microprocessor 089-XXX-004 (Failed Optional Microprocessor test) 1. VRM for Optional Microprocessor 4 2. Optional Microprocessor 165-XXX-000 (Failed Service Processor test) 1. Check error log for any I2C messages (see "I2C bus fault messages" on page 239). 2. Remove ac power from system for 20 seconds, then rerun service processor test. If problem persists, proceed to step 3.. 3. I/O Legacy Board. Before replacing the I/O Legacy Board, ensure that I/O Legacy Board jumper J28 is not installed (the default) when the error occurs. 180-XXX-000 (Diagnostics LED failure) 1. Run Diagnostic LED test for the failing LED. 180-XXX-001 (Failed information LED 1. Information LED Panel panel test) 2. Diagnostic LED Panel 3. I/O Legacy Board 180-XXX-002 Panel test) (Failed Diagnostics LED 1. Diagnostics LED Panel 2. I/O Legacy Board 180-XXX-003 LED test) (Failed System Board 1. System Board 180-XXX-004 Board LED test) (Failed Processor 1. Processor/PCI Board 2. I/O Legacy Board 180-XXX-005 (Failed SCSI Backplane LED test) 1. SCSI Backplane 2. SCSI Backplane Cable 3. I/O Legacy Board 180-XXX-006 (Memory Board LED test) 1. Memory Board 2. Processor/PCI Board 3. I/O Legacy Board 222 Hardware Maintenance Manual: Netfinity 7600 - Type 8665 Models 1RY, 2RY

Section	Page
About this manual	5
Important safety information	5
Online support	6
General checkout	11
General information	13
Features and specifications	13
Server features	15
Reliability, availability, and serviceability	16
Controls and indicators	17
Information LED panel	19
Diagnostics	21
Diagnostic tools overview	21
POST	22
Small computer system interface messages	22
Solving ServeRAID problems	23
Diagnostic programs and error messages	34
Light path diagnostics	37
Power checkout	41
Temperature checkout	41
Recovering BIOS	42
Replacing the battery	42
Diagnosing errors	44
Configuring the server	53
Using the Configuration/Setup Utility program	53
Using the SCSISelect utility program	59
Installing options	63
Major components of the Netfinity 7600	63
Component locations	64
Before you begin	70
Removing the server top cover and bezel	71
Working with adapters	73
Installing internal drives	76
Installing memory-module kits	81
Installing a microprocessor kit	83
Installing a hot-swap power supply	86
Replacing a hot-swap fan	88
Completing the installation	89
Connecting external options	91
Input/output ports	91
Cabling the server	103
Installing the server in a rack	103
Netfinity Manager	105
Managing your IBM Netfinity server with Netfinity Manager	106
Netfinity Manager documentation	106
Netfinity Manager system requirements	106
Starting the Netfinity Manager installation program	108
Netfinity Manager database support	115
Starting Netfinity Manager	125
Getting more information about Netfinity Manager	132
Installation options	133
FRU information (service only)	137
Diagnostic switch card	137
Disconnecting the shuttle	138
Front LED card assembly	138
I/O Legacy board	139
Memory card removal	140
PCI switch card	142
Power backplane assembly	142
Processor/PCI backplane	143
Removing the shuttle	145
SCSI backplane assembly	145
SCSI daughter card	146
Installing and configuring ServeRAID controllers	149
Features and connector locations of ServeRAID-4H controller	149
Features and connector locations of ServeRAID-4L controller	151
Features and connector locations of ServeRAID-4M controller	153
Using a ServeRAID-4x controller in a server with Hot-plug PCI features	155
Step 1: Installing and cabling a ServeRAID controller	156
Step 2: Updating BIOS and firmware code	161
Step 3: Configuring ServeRAID controllers	161
Obtaining ServeRAID updates	172
ServeRAID device driver order on Windows 2000 and Windows NT 4.0	174
Using utility programs	175
Introduction to IBM ServeRAID cluster solution	185
Monitoring and updating an IBM ServeRAID cluster solution	186
POST (ISPR) error codes and procedures	190
Recovery procedures for defunct (DDD) drives	194
Channel record table	201
Reference information	202
Symptom-to-FRU index	225
Beep symptoms	225
No beep symptoms	228
Diagnostic panel LEDs	228
Diagnostic error codes	230
Error symptoms	235
Power supply LED errors	235
POST error codes	236
ServeRAID POST (ISPR) error codes	242
ServeRAID	244
SCSI error codes	246
Temperature error messages	246
Fan error messages	247
Power error messages	247
System shutdown	248
DASD checkout	249
Host Built-In Self Test (BIST) checkout	249
I2C bus fault messages	249
Undetermined problems	251
Parts listing (Type 8665)	253
Part A	253
Part B	254
System	255
Keyboards	256
Power cords	257
Related service information	259
Safety information	259
Send us your comments!	289
Problem determination tips	290
Notices	290

Match case Limit results 1 per page

222

Hardware Maintenance Manual: Netfinity 7600

–

Type 8665 Models 1RY, 2RY

035-XXX-SNN

(Check System Error

Log before replacing a FRU.

S =

number of failing PCI slot; NN = SCSI ID

of failing fixed disk.)

Fixed Disk with SCSI ID NN on RAID adapter in PCI slot S.

035-253-S99

(RAID adapter

initialization failure)

ServeRAID Adapter in slot S is not configured properly.

Obtain the

basic and extended configuration status and refer to the ServeRAID

Hardware Maintenance Manual for more information.

Cable

SCSI Backplane

Adapter

075-XXX-000

(Failed Power Supply

test)

Power Supply

089-XXX-001

(Failed Microprocessor

test)

VRM for Microprocessor 1

Microprocessor

089-XXX-002

(Failed

Optional Microprocessor test)

VRM for Optional Microprocessor 2

Optional Microprocessor

089-XXX-003

(Failed Optional

Microprocessor test)

VRM for Optional Microprocessor 3

Optional Microprocessor

089-XXX-004

(Failed Optional

Microprocessor test)

VRM for Optional Microprocessor 4

Optional Microprocessor

165-XXX-000

(Failed Service

Processor test)

Check error log for any I2C messages

(see

“

I2C bus fault messages

”

on page 239).

Remove ac power from system for 20 seconds, then rerun service

processor test.

If problem persists, proceed to step 3..

I/O Legacy Board.

Before replacing the I/O Legacy Board, ensure that

I/O Legacy Board jumper J28 is not installed (the default) when the

error occurs.

180-XXX-000

(Diagnostics LED failure)

Run Diagnostic LED test for the failing LED.

180-XXX-001

(Failed information LED

panel test)

Information LED Panel

Diagnostic LED Panel

I/O Legacy Board

180-XXX-002

(Failed Diagnostics LED

Panel test)

Diagnostics LED Panel

I/O Legacy Board

180-XXX-003

(Failed System Board

LED test)

System Board

180-XXX-004

(Failed Processor

Board LED test)

Processor/PCI Board

I/O Legacy Board

180-XXX-005

(Failed SCSI

Backplane LED test)

SCSI Backplane

SCSI Backplane Cable

I/O Legacy Board

180-XXX-006

(Memory Board LED test)

Memory Board

Processor/PCI Board

I/O Legacy Board

Error Code/Symptom

FRU/Action