Home » IBM Manuals » Desktops » IBM 86655RY » Manual Viewer

IBM 86655RY Hardware Maintenance Manual - Page 29

Basic and Extended Configuration Status Register Codes, Controller 1 Slot 5

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

BCS Code not in table 00 00 00 01 01 01 01 01 For example: Controller 1 Slot 5, Status:Not responding properly - Error Code=0B0 Controller 2 Slot 4, Logical Drive=0, Other=0, Firmware=2.88.10, Status=Ok Controller 3 Slot 3, Logical Drive=0, Other=0, Firmware=3.60.13, Status=Ok Controller 4 Slot 2, Logical Drive=1, Other=1, Firmware=1.00.09, Status=Ok If no errors occur: ISPR (aaaa) = EF10 BCS (bb) = 0F or 09 ECS (cc) = 00 If an error occurs, refer to: "ServeRAID POST (ISPR) error codes" on page 232 for the ISPR error codes and "Basic and Extended Configuration Status Register Codes" for the BCS and ECS error codes. Basic and Extended Configuration Status Register Codes: ECS Explanation and possible recovery action Code not in table Explanation: The ServeRAID controller is not functioning properly. Action: Replace the adapter or the I/O board with integrated controller. 01 Explanation: Invalid flash configuration. Action: Start the IBM ServeRAID Support CD and follow the instructions that appear on the screen. 02 Explanation: Invalid NVRAM configuration. Action: Start the IBM ServeRAID Support CD and follow the instructions that appear on the screen. 03 Explanation: Invalid flash and NVRAM configuration. Action: Start the IBM ServeRAID Support CD and follow the instructions that appear on the screen. 08 Explanation: No configuration was found in drives, or online/rebuild drives are not responding. Action: Press F4, F5, F7, or F10. 18 Explanation: No configuration was found in drives, or online/rebuild and hot- spare/standby hot-spare drives are not responding. Action: Press F4, F5, F7, or F10. 28 Explanation: No configuration was found in drives, or online/rebuild and ready/standby drives are not responding. Action: Press F4, F5, F7, or F10. 38 Explanation: No configuration was found in drives, or online/rebuild, hot- spare/standby hot-spare, and ready/standby drives are not responding. Action: Press F4, F5, F7, or F10. 48 Explanation: No configuration was found in drives, or online/rebuild drives are not responding and unidentified drives were found. Action: Press F4, F5, F7, or F10. Diagnostics 19

Section	Page
About this manual	5
Important safety information	5
Online support	6
General checkout	11
General information	13
Features and specifications	13
Server features	15
Reliability, availability, and serviceability	16
Controls and indicators	17
Information LED panel	19
Diagnostics	21
Diagnostic tools overview	21
POST	22
Small computer system interface messages	22
Solving ServeRAID problems	23
Diagnostic programs and error messages	34
Light path diagnostics	37
Power checkout	41
Temperature checkout	41
Recovering BIOS	42
Replacing the battery	42
Diagnosing errors	44
Configuring the server	53
Using the Configuration/Setup Utility program	53
Using the SCSISelect utility program	59
Installing options	63
Major components of the Netfinity 7600	63
Component locations	64
Before you begin	70
Removing the server top cover and bezel	71
Working with adapters	73
Installing internal drives	76
Installing memory-module kits	81
Installing a microprocessor kit	83
Installing a hot-swap power supply	86
Replacing a hot-swap fan	88
Completing the installation	89
Connecting external options	91
Input/output ports	91
Cabling the server	103
Installing the server in a rack	103
Netfinity Manager	105
Managing your IBM Netfinity server with Netfinity Manager	106
Netfinity Manager documentation	106
Netfinity Manager system requirements	106
Starting the Netfinity Manager installation program	108
Netfinity Manager database support	115
Starting Netfinity Manager	125
Getting more information about Netfinity Manager	132
Installation options	133
FRU information (service only)	137
Diagnostic switch card	137
Disconnecting the shuttle	138
Front LED card assembly	138
I/O Legacy board	139
Memory card removal	140
PCI switch card	142
Power backplane assembly	142
Processor/PCI backplane	143
Removing the shuttle	145
SCSI backplane assembly	145
SCSI daughter card	146
Installing and configuring ServeRAID controllers	149
Features and connector locations of ServeRAID-4H controller	149
Features and connector locations of ServeRAID-4L controller	151
Features and connector locations of ServeRAID-4M controller	153
Using a ServeRAID-4x controller in a server with Hot-plug PCI features	155
Step 1: Installing and cabling a ServeRAID controller	156
Step 2: Updating BIOS and firmware code	161
Step 3: Configuring ServeRAID controllers	161
Obtaining ServeRAID updates	172
ServeRAID device driver order on Windows 2000 and Windows NT 4.0	174
Using utility programs	175
Introduction to IBM ServeRAID cluster solution	185
Monitoring and updating an IBM ServeRAID cluster solution	186
POST (ISPR) error codes and procedures	190
Recovery procedures for defunct (DDD) drives	194
Channel record table	201
Reference information	202
Symptom-to-FRU index	225
Beep symptoms	225
No beep symptoms	228
Diagnostic panel LEDs	228
Diagnostic error codes	230
Error symptoms	235
Power supply LED errors	235
POST error codes	236
ServeRAID POST (ISPR) error codes	242
ServeRAID	244
SCSI error codes	246
Temperature error messages	246
Fan error messages	247
Power error messages	247
System shutdown	248
DASD checkout	249
Host Built-In Self Test (BIST) checkout	249
I2C bus fault messages	249
Undetermined problems	251
Parts listing (Type 8665)	253
Part A	253
Part B	254
System	255
Keyboards	256
Power cords	257
Related service information	259
Safety information	259
Send us your comments!	289
Problem determination tips	290
Notices	290

Match case Limit results 1 per page

Diagnostics

For example:

Controller 1 Slot 5, Status:Not responding properly - Error Code=0B0

Controller 2 Slot 4, Logical Drive=0, Other=0, Firmware=2.88.10, Status=Ok

Controller 3 Slot 3, Logical Drive=0, Other=0, Firmware=3.60.13, Status=Ok

Controller 4 Slot 2, Logical Drive=1, Other=1, Firmware=1.00.09, Status=Ok

If no errors occur:

ISPR (

aaaa

) = EF10

BCS (

) = 0F or 09

ECS (

) = 00

If an error occurs, refer to:

“

ServeRAID POST (ISPR) error codes

”

on page 232 for the

ISPR error codes and

“

Basic and Extended Configuration Status Register Codes

”

for

the BCS and ECS error codes.

Basic and Extended Configuration Status Register Codes:

BCS

ECS

Explanation and possible recovery action

Code not in

table

Code not in

table

Explanation:

The ServeRAID controller is not functioning properly.

Action:

Replace the adapter or the I/O board with integrated controller.

Explanation:

Invalid flash configuration.

Action:

Start the

IBM ServeRAID Support CD

and follow the instructions that appear

on the screen.

Explanation:

Invalid NVRAM configuration.

Action:

Start the

IBM ServeRAID Support CD

and follow the instructions that appear

on the screen.

Explanation:

Invalid flash and NVRAM configuration.

Action:

Start the

IBM ServeRAID Support CD

and follow the instructions that appear

on the screen.

Explanation:

No configuration was found in drives, or online/rebuild drives are not

responding.

Action:

Press F4, F5, F7, or F10.

Explanation:

No configuration was found in drives, or online/rebuild and hot-

spare/standby hot-spare drives are not responding.

Action:

Press F4, F5, F7, or F10.

Explanation:

No configuration was found in drives, or online/rebuild and

ready/standby drives are not responding.

Action:

Press F4, F5, F7, or F10.

Explanation:

No configuration was found in drives, or online/rebuild, hot-

spare/standby hot-spare, and ready/standby drives are not responding.

Action:

Press F4, F5, F7, or F10.

Explanation:

No configuration was found in drives, or online/rebuild drives are not

responding and unidentified drives were found.

Action:

Press F4, F5, F7, or F10.