Netgear GS748Tv5 Software Administration Manual - Page 148

Con IP Settings, IP Configuration, To enable routing on the switch, Routing, Enable, Apply

Page 148 highlights

GS716Tv3, GS724Tv4, and GS748Tv5 Smart Switches Configure IP Settings For information about how to configure and display IP routing data, see the following sections: • IP Configuration • VLAN Routing Wizard • IP Statistics IP Configuration Use the IP Configuration screen to configure routing parameters for the switch.  To enable routing on the switch: 1. Select Routing > IP > IP Configuration. 2. Next to Routing Mode, select Enable. You must enable routing for the switch before you can route through any of the interfaces. Routing is also enabled or disabled per VLAN interface. The default value is Disable. 3. Click the Apply button. The following table describes the IP configuration information displayed on the screen. Table 50. Global IP status information Field Default Time to Live Maximum Next Hops Description The default value inserted into the Time-To-Live field of the IP header of datagrams originated by the switch, if a TTL value is not supplied by the transport layer protocol. The default value is 64. The maximum number of hops supported by the switch. This is a compile-time constant. The default value is 1. Configuring Routing 148

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290

Configuring Routing
148
GS716Tv3, GS724Tv4, and GS748Tv5 Smart Switches
Configure IP Settings
For information about how to configure and display IP routing data, see the following
sections:
IP Configuration
VLAN Routing Wizard
IP Statistics
IP Configuration
Use the IP Configuration screen to configure routing parameters for the switch.
To enable routing on the switch:
1.
Select
Routing
>
IP
>
IP Configuration
.
2.
Next to Routing Mode, select
Enable
.
You must enable routing for the switch before you can route through any of the interfaces.
Routing is also enabled or disabled per VLAN interface. The default value is Disable.
3.
Click the
Apply
button.
The following table describes the IP configuration information displayed on the screen.
Table 50.
Global IP status information
Field
Description
Default Time to Live
The default value inserted into the Time-To-Live field of the IP
header of datagrams originated by the switch, if a TTL value is not
supplied by the transport layer protocol. The default value is 64.
Maximum Next Hops
The maximum number of hops supported by the switch. This is a
compile-time constant. The default value is 1.