Panasonic AG-HPD24PJ Operating Instructions - Page 146

Warning and Error Messages, Error Information

Get Panasonic AG-HPD24PJ PDF manuals and user guides View all Panasonic AG-HPD24PJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Warning and Error Messages For Long and Trouble-Free Operation When the unit generates a warning, the OSD of the record and playback screen shows an error number and an error message. When an operational malfunction occurs in the unit, an error number will flash on the OSD of the record and playback screen. Error Information The POWER lamp, the P2 card access lamp and a beep sound notify the operator of a malfunction that is detected during powering up or operation. The beep notification is enabled when the SETUP - BASIC - BEEP menu setting is set to ON (➝ Setup Menu "BASIC" - "BEEP" page 61). Monitor display*1 Warning message E-37, 38*2 System error POWER lamp Beep sound Blinks 4 time per second Repeated rapidly E-30*2 Blinks 4 time Incorrect P2 card removal per second Repeated rapidly E-31*2 Recording error Blinks 4 times Repeated per second rapidly E-BA Displayed during a preset time period*2 The battery is depleted. Blinks 1 time per second Repeated rapidly E-21*2 Recording error Blinks 4 time per second Repeated rapidly E-80, 81, 83, 84*2 Connection error One remaining battery capacity indicator blinks Battery nearly empty Blinks 4 time per second Repeated rapidly Blinks 1 time per second None Description Countermeasure P2 microprocessor or control failure. Operation stops. To continue operation, turn the power off and then back on again. A P2 card was removed during access and an error occurred in inner memory. Turn the unit off. Repair any clips on the removed P2 card that are corrupted. Recorded data is corrupted. Turn the power off, then turn it on again and try again. Replace a P2 card that does not enable normal recording. The battery is depleted. Recording and playback Replace the battery with a stop. The unit is turned off freshly charged battery. automatically when the voltage drops further. A recording error has occurred. Stop recording. Turn the power off , then turn it on again and try again. Replace a P2 card that does not enable normal recording. Stop (STOP) and start playback to clear the error, displayed error message and beep sound. A malfunction has occurred in the 3D REC/ PB mode or SYNC PB mode system. Turn the power off and check the connections and other factors. The battery is near depletion. Replace the battery as necessary. *1 Same range of destination output set in the SETUP - DISPLAY - OSD OUTPUT menu setting. *2 For details on display location, refer to the OSD display (➝ Setup Menu "DISPLAY" - "OSD OUTPUT" page 67). The error number and "AUTO OFF" are alternately displayed. 83 For Long and Trouble-Free Operation: Warning and Error Messages

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
For Long and Trouble-Free Operation: Warning and Error Messages
83
For Long and Trouble-Free Operation
Warning and Error Messages
When the unit generates a warning, the OSD of the record and playback screen shows an error number and an error message.
When an operational malfunction occurs in the unit, an error number will flash on the OSD of the record and playback screen.
The POWER lamp, the P2 card access lamp and a beep sound notify the operator of a malfunction that is detected during
powering up or operation.
The beep notification is enabled when the SETUP - BASIC - BEEP menu setting is set to ON (
➝
Setup Menu “BASIC” - “BEEP”
page 61).
*
1
Same range of destination output set in the SETUP - DISPLAY - OSD OUTPUT menu setting.
*
2
For details on display location, refer to the OSD display (
➝
Setup Menu “DISPLAY” - “OSD OUTPUT” page 67). The error
number and “AUTO OFF” are alternately displayed.
Error Information
Monitor display
*
1
Warning message
POWER lamp
Beep sound
Description
Countermeasure
E-37, 38
*
2
System error
Blinks 4 time
per second
Repeated
rapidly
P2 microprocessor or
control failure. Operation
stops.
To continue operation,
turn the power off and
then back on again.
E-30
*
2
Incorrect P2 card removal
Blinks 4 time
per second
Repeated
rapidly
A P2 card was removed
during access and an
error occurred in inner
memory.
Turn the unit off. Repair
any clips on the removed
P2 card that are
corrupted.
E-31
*
2
Recording error
Blinks 4 times
per second
Repeated
rapidly
Recorded data is
corrupted.
Turn the power off, then
turn it on again and try
again. Replace a P2 card
that does not enable
normal recording.
E-BA
Displayed during a
preset time period
*
2
The battery is depleted.
Blinks 1 time
per second
Repeated
rapidly
The battery is depleted.
Recording and playback
stop. The unit is turned off
automatically when the
voltage drops further.
Replace the battery with a
freshly charged battery.
E-21
*
2
Recording error
Blinks 4 time
per second
Repeated
rapidly
A recording error has
occurred.
Stop recording.
Turn the power off , then
turn it on again and try
again. Replace a P2 card
that does not enable
normal recording. Stop
(STOP) and start
playback to clear the
error, displayed error
message and beep
sound.
E-80, 81, 83, 84
*
2
Connection error
Blinks 4 time
per second
Repeated
rapidly
A malfunction has
occurred in the 3D REC/
PB mode or SYNC PB
mode system.
Turn the power off and
check the connections
and other factors.
One remaining
battery capacity
indicator blinks
Battery nearly empty
Blinks 1 time
per second
None
The battery is near
depletion.
Replace the battery as
necessary.