Panasonic AG-HPD24PJ Operating Instructions - Page 48

Synchronous Playback, Connections, Selecting SYNC PB Mode

Get Panasonic AG-HPD24PJ PDF manuals and user guides View all Panasonic AG-HPD24PJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Synchronous Playback Left/right 3D clip pairs not recorded in dual P2 3D mode can be played back using the synchronous playback (SYNC PB) mode. Connect two AG-HPD24 units in the same way as for 3D REC/PB mode, and press the MODE button to select the SYNC PB mode for synchronous video playback operation of the slave with the master unit. However, this mode does not support clip operations other than playback (that is, recording, copying and deleting). 3D clip content not recorded as a Dual P2 3D clip: Clips dubbed from material recorded on an AG-3DA1 with their starting points trued up and length set to be equal using an AJ-HPM200, or clips edited using a non-linear editor and dubbed to a P2 unit that does not support Dual P2 3D recording. The L and R clips are required to have the same time code start point, length, and clip sequence. ◆ NOTE: • Insert the P2 cards with the left-eye (L) and right-eye (R) recordings into P2 card slots on the master side and slave sides, respectively. Connections Connections are the same as for 3D REC/PB mode. (➝ "3D Signal Recording and Playback" "Connections" page 39) Selecting SYNC PB Mode 1 Connect two units according to the connection examples. ◆ NOTE: • The system frequency cannot be changed when SYNC PB mode is enabled. Set the frequency before selecting the mode. • Set the master and slave units to the same frequency. • The SYNC PB mode cannot be enabled when the system frequency is set to "59-23" or "60-24". Select the frequency to be used before selecting the SYNC PB mode. 2 Press the MODE button on the master unit. The mode selection menu appears. 3 Select SYNC PB. Use the Up/Down cursor buttons to place a " " at SYNC PB, and press the SET button. 4 Both master and slave units restart in SYNC PB mode. 48 Synchronous Playback: Connections

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
48
Synchronous Playback: Connections
Synchronous Playback
Left/right 3D clip pairs not recorded in dual P2 3D mode can be played back using the synchronous
playback (SYNC PB) mode. Connect two AG-HPD24 units in the same way as for 3D REC/PB mode, and
press the MODE button to select the SYNC PB mode for synchronous video playback operation of the
slave with the master unit. However, this mode does not support clip operations other than playback
(that is, recording, copying and deleting).
3D clip content not recorded as a Dual P2 3D clip:
Clips dubbed from material recorded on an AG-3DA1 with their starting points trued up and length set to
be equal using an AJ-HPM200, or clips edited using a non-linear editor and dubbed to a P2 unit that does
not support Dual P2 3D recording.
The L and R clips are required to have the same time code start point, length, and clip sequence.
◆
NOTE:
• Insert the P2 cards with the left-eye (L) and right-eye (R) recordings into P2 card slots on the master
side and slave sides, respectively.
Connections are the same as for 3D REC/PB mode. (
➝
“3D Signal Recording and Playback” -
“Connections” page 39)
1
Connect two units according to the
connection examples.
◆
NOTE:
• The system frequency cannot be changed
when SYNC PB mode is enabled. Set the
frequency before selecting the mode.
• Set the master and slave units to the same
frequency.
• The SYNC PB mode cannot be enabled
when the system frequency is set to “59-23”
or “60-24”. Select the frequency to be used
before selecting the SYNC PB mode.
2
Press the MODE button on the master unit.
The mode selection menu appears.
3
Select SYNC PB.
Use the Up/Down cursor buttons to place a
“
” at SYNC PB, and press the SET button.
4
Both master and slave units restart in
SYNC PB mode.
Connections
Selecting SYNC PB Mode