Dell PowerEdge R415 Hardware Owner's Manual - Page 114

iDRAC6 Enterprise Card (Optional), Removing an iDRAC6 Enterprise Card

Get Dell PowerEdge R415 PDF manuals and user guides View all Dell PowerEdge R415 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

4 Align the front edge of the card with the connector on the system board. See Figure 6-1 for the location of the connector. 5 Press the card down until it is fully seated. See Figure 3-18. When the front of the card is fully seated, the plastic standoff tab snaps over the edge of the holder. 6 Close the system. See "Closing the System" on page 83. 7 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. iDRAC6 Enterprise Card (Optional) Removing an iDRAC6 Enterprise Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 If present, disconnect the Ethernet cable from the iDRAC6 enterprise card connector on the system back panel. See Figure 1-4. 3 Open the system. See "Opening the System" on page 82. 4 Remove the system board shroud. See "Removing the System Board Shroud" on page 109. 5 Remove the VFlash media card (if applicable) from the iDRAC6 enterprise card. See "Removing a VFlash Media Card" on page 116. 6 Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs. As the card releases from the standoffs, the connector under the card disengages from the system board connector. 7 Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system. 114 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
114
Installing System Components
4
Align the front edge of the card with the connector on the system board.
See Figure 6-1 for the location of the connector.
5
Press the card down until it is fully seated. See Figure 3-18.
When the front of the card is fully seated, the plastic standoff tab snaps
over the edge of the holder.
6
Close the system. See "Closing the System" on page 83.
7
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
iDRAC6 Enterprise Card (Optional)
Removing an iDRAC6 Enterprise Card
CAUTION:
Many repairs may only be done by a certified service technician.
You should only perform troubleshooting and simple repairs as authorized in
your product documentation, or as directed by the online or telephone service
and support team. Damage due to servicing that is not authorized by Dell is
not covered by your warranty. Read and follow the safety instructions that
came with the product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
If present, disconnect the Ethernet cable from the iDRAC6 enterprise card
connector on the system back panel. See Figure 1-4.
3
Open the system. See "Opening the System" on page 82.
4
Remove the system board shroud. See "Removing the System Board
Shroud" on page 109.
5
Remove the VFlash media card (if applicable) from the iDRAC6
enterprise card. See "Removing a VFlash Media Card" on page 116.
6
Pull back slightly on the two tabs at the front edge of the card and gently
lift the front edge of the card off of the retention standoffs.
As the card releases from the standoffs, the connector under the card
disengages from the system board connector.
7
Slide the card away from the back of the system until the RJ-45 connector
is clear of the back panel, then lift the card out of the system.