Denon AVR-5805MK2 Owners Manual - Page 174

16 TROUBLESHOOTING If a problem should arise,first check the following. 1. Are the connections correct? 2. Have you operated the receiver according to the Operating Instructions? 3. Are the speakers, and other connected components operating properly? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase. Symptom DISPLAY not lit and sound not produced when power switch set to on. DISPLAY lit but sound not produced. Nothing is displayed on monitor. No DTS sound is produced. Ultra2 Cinema / THX Music Mode / THX Games Mode cannnot be set. Copying from DVD to VCR is not possible. No sound is produced from subwoofer. No test tones are produced. No sound is produced from surround speakers. This unit does not operate properly when Remote control unit is used. An image is not projected with an HDMI/DVI-D connection. The HDMI audio is not output. Cause • Power cord not plugged in securely. • Speaker cords not securely connected. • FUNCTION knob position is not appropriate. • Volume control set to minimum. • MUTING is on. • No digital signal is being input. • AVR-5805's video output jacks and monitor's input jacks are not properly connected. • Monitor TV's input setting is wrong. • The VIDEO OFF mode is set. • The PURE DIRECT mode is set. • The resolution of the monitor device connected to the component monitor output connector does not match the AVR-5805's resolution. • DVD player's audio output setting is not set to bit stream. • DVD player is not DTS-compatible. • AVR-5805's input setting is set to analog. • Surround back speaker set to 1. • Copying between a source such as DVD and a VCR is not usually possible, as DVDs are often encoded with copy-protection signals that prevent VCR recording. • Subwoofer's power is not on. • Subwoofer's initial setting is set to "NO". • Subwoofer's output is not connected. • Surround mode is set to a mode other than Dolby Surround. • Surround mode is set to "STEREO". • Batteries dead. • Remote control unit too far from this unit. • Obstacle between this unit and Remote control unit. • Different button is being pressed. • < and > ends of battery inserted in reverse. • AVR-5805's HDMI/DVI-D output jacks and monitor's input jacks are not properly connected. • No HDMI/DVI-D signal is being input. • The connected monitor equipment or other equipments do not spport HDCP. • The settings of "MONITOR SELECT" is not appropriate. • The output format of the connected player (HDMI/DVI-D FORMAT) does not matche the supported input format of connected monitor equipments. • The AVR-5805 does not play HDMI audio signals. • The HDMI audio signals are not output from the connected monitor device. Measures • Check the insertion of the power cord plug. • Connect securely. • Switch to the proper position. • Turn volume up to suitable level. • Switch off MUTING. • Properly select a digital signal input source. • Check that the connections are correct. • Set the TV's input selector to the jacks to which video signals are connected. • Set the VIDEO ON mode. • Set a surround mode other than the PURE DIRECT mode. • Use the SCALE button on the main unit or the remote control unit to check the resolution setting. • Make the DVD player's initial settings. • Use a DTS-compatible player. • Set to AUTO or DTS. • Connect two surround back speakers. • Copying is not possible. • Turn on the power. • Set the setting to "YES". • Connect properly. • Set to Dolby Surround. • Set to a mode other than "STEREO". • Replace with new batteries. • Move closer. • Remove obstacle. • Press the proper button. • Insert batteries properly. • Check the HDMI/DVI-D connection. • Properly select HDMI or DVI-D signal input source. • The AVR-5805 will not output video signal unless the other equipment supports HDCP. • Check the settings of "MONITOR SELECT". • Check whether the output format of the connected player (HDMI/DVI-D FORMAT) matches the supported input format of connected monitor equipments. • Set the HDMI audio playback setting at the "HDMI/DVI In Assign" settings to "AMP". • Set the HDMI audio playback setting at the "HDMI/DVI In Assign" settings to "TV". Page 10 20, 21 126 127 130 58 11~15 - 129 129 132 - - 126 29, 46, 47, 57, - - 46, 47 21, 99, 100, 00 - - 113 113 113 - 113 14, 15 75, 76 14, 15 75, 76, 131,00 75, 76 75, 76 75, 76 174