Fluke 744 Fluke 744 Users Manual - Page 48

orientation. See Attach the RTD to input jacks as the display or

Page 48 highlights

744 Users Manual To measure temperature using an RTD input, proceed as follows: 1. If necessary, press M for MEASURE mode. 2. Press t twice so that Select RTD Type shows. 3. Press u or d to select the desired RTD type. 4. Press e. 5. Press u or d to select a 2-, 3-, or 4- wire connection. 6. Attach the RTD to input jacks as the display or Figure 15 shows. Use the supplied jumper between the mA Ω RTD MEAS low jack and the V MEAS low jack as shown if you are using a 3wire connection. 7. Press e. Caution Do not force a dual banana plug between any two jacks in the horizontal orientation. Doing so will damage the jacks. Use the supplied jumper wire when needed for RTD measurements. You can use a dual banana plug in the vertical orientation. See Figure 14. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138

744
Users Manual
38
To measure temperature using an RTD input,
proceed as follows:
1.
If necessary, press
M
for MEASURE mode.
2.
Press
t
twice so that
Select RTD Type
shows.
3.
Press
u
or
d
to select the desired RTD type.
4.
Press
e
.
5.
Press
u
or
d
to select a 2-, 3-, or 4- wire
connection.
6.
Attach the RTD to input jacks as the display or
Figure 15 shows. Use the supplied jumper
between the mA
RTD MEAS low jack and the
V MEAS low jack as shown if you are using a 3-
wire connection.
7.
Press
e
.
Caution
Do not force a dual banana plug between
any two jacks in the horizontal
orientation. Doing so will damage the
jacks. Use the supplied jumper wire when
needed for RTD measurements. You can
use a dual banana plug in the vertical
orientation. See Figure 14.