Fluke 744 Fluke 744 Users Manual - Page 96

Recording Min and Max Measurements, Running a Preloaded Task, Clearing Memory, Min Max data

Get Fluke 744 PDF manuals and user guides View all Fluke 744 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

744 Users Manual Recording Min and Max Measurements You can set the display to record and show the maximum and minimum readings. Min and Max readings are always undamped, even if Dampen is On. Press the More Choices softkey twice, then press the Min Max softkey to turn on this feature. Press the c key to reset the Min Max registers. Press the Min Max softkey again to revert to the normal display. The following figure shows the display with Min Max on: gj55s.eps 86 Running a Preloaded Task Press the More Choices softkey until the Tasks softkey appear, then press Tasks to view the list of tasks (procedures) downloaded from a host computer. Tasks are calibrator configurations, saved with a procedure name, for example the type and manufacturer of a specific transmitter. A task configures the calibrator for transmitter calibration with all the calibration parameters (source and measure functions, 0% and 100% levels, test strategy) predefined. While the task is controlling the calibrator, the Continue softkey becomes Continue Task. Clearing Memory In Setup mode, highlight the Clear Memory choice and press e to clear all the memory: • Saved results • Min Max data • Log data sets A confirmation message appears so that you do not inadvertently erase the memory.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
744
Users Manual
86
Recording Min and Max Measurements
You can set the display to record and show the
maximum and minimum readings. Min and Max
readings are always undamped, even if Dampen is
On. Press the
More Choices
softkey twice, then press
the
Min Max
softkey to turn on this feature. Press the
c
key to reset the Min Max registers. Press the
Min Max
softkey again to revert to the normal display.
The following figure shows the display with Min Max
on:
gj55s.eps
Running a Preloaded Task
Press the
More Choices
softkey until the
Tasks
softkey appear, then press
Tasks
to view the list of
tasks (procedures) downloaded from a host
computer. Tasks are calibrator configurations, saved
with a procedure name, for example the type and
manufacturer of a specific transmitter. A task
configures the calibrator for transmitter calibration
with all the calibration parameters (source and
measure functions, 0% and 100% levels, test
strategy) predefined.
While the task is controlling the calibrator, the
Continue
softkey becomes
Continue Task
.
Clearing Memory
In Setup mode, highlight the
Clear Memory
choice
and press
e
to clear all the memory:
•
Saved results
•
Min Max data
•
Log data sets
A confirmation message appears so that you do not
inadvertently erase the memory.