Garmin iQue M5 Que Applications Guide - Page 54

Vehicle Installation, To install the suction mount

Get Garmin iQue M5 - Win Mobile For Pocket PC 2003 2nd Ed 416 MHz PDF manuals and user guides
UPC - 753759047276
View all Garmin iQue M5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

APPENDIX > VEHICLE INSTALLATION Vehicle Installation Your iQue M5 comes with a suction mount that attaches easily to your vehicle's windshield. Be sure to place the suction mount so that it does not block your field of vision and so that you can plug in the DC adapter cable easily. Pivoting joint rotates to the left or right. Auto Cradle Suction Cup Adjusting Knobs Cam Lever (shown in the Down position) 50 To install the suction mount: 1. Extend the suction mount by loosening the two adjusting knobs on the right side of the mount. Then adjust each section of the mount. When you are finished extending the mount, lightly tighten the adjustment knobs to keep each section in place. You can also adjust the angle of the Auto cradle by rotating the pivoting joint to the left or right 2. Thoroughly clean the inside surfaces of both the windshield and the mount's suction cup (use rubbing alcohol if possible) and allow both to air dry completely. 3. Make sure the suction cam lever is Up. Then place the suction mount in the desired location on your windshield. Verify that you can plug in the DC adapter easily. 4. Place the suction cup firmly against the glass and wiggle it to remove as much air as possible. Then press the cam lever down (toward the windshield) and apply gentle pressure to the mount so that the suction cup grips the windshield firmly. iQue M5 Que Applications Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
50
iQue M5 Que Applications Guide
A
PPENDIX
>
V
EHICLE
I
NSTALLATION
Vehicle Installation
Your iQue M5 comes with a suction mount that
attaches easily to your vehicle’s windshield. Be sure
to place the suction mount so that it does not block
your field of vision and so that you can plug in the DC
adapter cable easily.
Adjusting Knobs
Auto Cradle
Cam Lever
(shown in the
Down position)
Suction Cup
Pivoting joint rotates to the left or right.
To install the suction mount:
1.
Extend the suction mount by loosening the two
adjusting knobs on the right side of the mount.
Then adjust each section of the mount. When
you are finished extending the mount, lightly
tighten the adjustment knobs to keep each
section in place.
You can also adjust the angle of the Auto cradle
by rotating the pivoting joint to the left or right
2.
Thoroughly clean the inside surfaces of both
the windshield and the mount’s suction cup (use
rubbing alcohol if possible) and allow both to air
dry completely.
3.
Make sure the suction cam lever is Up. Then
place the suction mount in the desired location
on your windshield. Verify that you can plug in
the DC adapter easily.
4.
Place the suction cup firmly against the glass
and wiggle it to remove as much air as possible.
Then press the cam lever down (toward the
windshield) and apply gentle pressure to
the mount so that the suction cup grips the
windshield firmly.