Icom IC-9700 Instruction Manual advanced - Page 37

Programmed scan, Programmed scan operation

Get Icom IC-9700 PDF manuals and user guides View all Icom IC-9700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

5. SCANS Programmed scan Programmed scan and Fine Programmed scan Scan edge 1A ~ 3A Scan edge 1B ~ 3B Scan Jump Repeatedly scans between two Scan Edge frequencies (1A/1B ~ 3A/3B channels). LTo change the Scan Edge Memory channels, see "Entering memory channel contents" (p. 4-2) for details. LIf the same frequencies are entered into the Scan Edge Memory channels, the Programmed scan does not start. LThe Fine Programmed scan is most effective in the SSB, CW, and RTTY modes. DDProgrammed scan operation 1. Select the VFO mode. 2. Select the operating mode and tuning step. (Example: USB, 1 kHz) 3. Display the SCAN screen. MENU » SCAN 4. Touch [PROG] for 1 second. 5. Touch the frequency range to scan (example: P1) Blinks Blinks •• The Programmed scan starts. LWhen a signal is detected, the scan pauses according to the "SCAN Resume" setting, and then resumes. LYou can change the tuning step by touching kHz. LTo cancel the scan, touch [PROG]. 6. Touch [FINE] to switch to the Fine Programmed scan. Blinks •• The tuning step changes to the 50 Hz step. LLWhen a signal is detected, the tuning step changes to the 10 Hz step. LLTouch [FINE] again to return to the Programmed scan. 7. To close the SCAN screen, push EXIT . 5-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
5-4
5. SCANS
Programmed scan
Programmed scan and Fine Programmed scan
Scan
Scan edge
1A ~ 3A
Scan edge
1B ~ 3B
Jump
Repeatedly scans between two Scan Edge
frequencies (1A/1B ~ 3A/3B channels).
L
To change the Scan Edge Memory channels, see
“Entering memory channel contents” (p. 4-2) for details.
L
If the same frequencies are entered into the
Scan Edge Memory channels, the Programmed
scan does not start.
L
The Fine Programmed scan is most effective in
the SSB, CW, and RTTY modes.
D
Programmed scan operation
1.
Select the VFO mode.
2.
Select the operating mode and tuning step.
(Example: USB, 1 kHz)
3. Display the SCAN screen.
MENU
»
SCAN
4.
Touch [PROG] for 1 second.
5.
Touch the frequency range to scan (example: P1)
Blinks
Blinks
•
The Programmed scan starts.
L
When a signal is detected, the scan pauses
according to the “SCAN Resume” setting, and then
resumes.
L
You can change the tuning step by touching kHz.
L
To cancel the scan, touch [PROG].
6.
Touch [FINE] to switch to the Fine Programmed
scan.
Blinks
•
The tuning step changes to the 50 Hz step.
L
When a signal is detected, the tuning step changes
to the 10 Hz step.
L
Touch [FINE] again to return to the Programmed scan.
7.
To close the SCAN screen, push
EXIT
.