Motorola WA840GP User Guide - Page 48

Options related to: OPTIMIZING LOCAL AREA NETWORK ROUTING, DHCP Ending IP - bridge

Get Motorola WA840GP - Wireless Access Point Router PDF manuals and user guides
UPC - 612572118740
View all Motorola WA840GP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Section 3 Configuration Field Description DHCP Ending IP Address: (ADVANCED) Sets the end of the IP address range that the DHCP server will lease to clients. By factory default this is set to offer the maximum number of concurrent IP address leases (253). NOTE: This field is ignored if the DHCP Server (above) is Disabled. FACTORY DEFAULT: 192.168.40.254 DHCP Lease Time: Sets the length of time (in seconds) that DHCP leases will be valid. By factory default this is set at 86,400 seconds, or 24 hours. (ADVANCED) NOTE: This field is ignored if the DHCP Server (above) is Disabled. FACTORY DEFAULT: 86400 Active DHCP Leases: (DISPLAY ONLY) Shows a list of the active DHCP leases since the last reboot. For each active lease, the client's host name, MAC address, IP address, and remaining lease duration are shown. Options related to: OPTIMIZING LOCAL AREA NETWORK ROUTING Field Spanning Tree Protocol: (ADVANCED) Static Routes: (ADVANCED) Description Enables use of the Ethernet 802.1d Spanning Tree Protocol, which eliminates bridging loops across the LAN connections. • Selecting Enabled engages the Spanning Tree Protocol. • Selecting Disabled disengages the Spanning Tree Protocol. NOTE: This setting is only used if Operation Mode on the BASIC Page is set to Router. FACTORY DEFAULT: Enabled Sets static routes to up to five specific clients on your local network. For each route, a Destination IP Address, Subnet Mask, and Gateway must be entered, along with the number of intermediate Access Points (or "Metric") between this Access Point and the client. NOTE: These settings are only used if Operation Mode on the BASIC Page is set to Router. FACTORY DEFAULT: (blank) 3-14 WA840

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Section 3
Configuration
3-14
WA840
Field
Description
DHCP Ending IP
Address:
(ADVANCED)
Sets the end of the IP address range that the DHCP server will lease
to clients.
By factory default this is set to offer the maximum number
of concurrent IP address leases (253).
NOTE
:
This field is ignored if the
DHCP Server
(above) is
Disabled.
FACTORY DEFAULT:
192.168.40.254
DHCP Lease
Time:
(ADVANCED)
Sets the length of time (in seconds) that DHCP leases will be valid.
By factory default this is set at 86,400 seconds, or 24 hours.
NOTE
:
This field is ignored if the
DHCP Server
(above) is
Disabled.
FACTORY DEFAULT:
86400
Active DHCP
Leases:
(DISPLAY ONLY)
Shows a list of the active DHCP leases since the last reboot.
For
each active lease, the client’s host name, MAC address, IP address,
and remaining lease duration are shown.
Options related to:
OPTIMIZING LOCAL AREA NETWORK ROUTING
Field
Description
Spanning Tree
Protocol:
(ADVANCED)
Enables use of the Ethernet 802.1d Spanning Tree Protocol, which
eliminates bridging loops across the LAN connections.
•
Selecting
Enabled
engages the Spanning Tree Protocol.
•
Selecting
Disabled
disengages the Spanning Tree Protocol.
NOTE
:
This setting is only used if
Operation Mode
on the BASIC Page
is set to
Router.
FACTORY DEFAULT:
Enabled
Static Routes:
(ADVANCED)
Sets static routes to up to five specific clients on your local network.
For each route, a Destination IP Address, Subnet Mask, and
Gateway must be entered, along with the number of intermediate
Access Points (or “Metric”) between this Access Point and the client.
NOTE
:
These settings are only used if
Operation Mode
on the BASIC
Page is set to
Router.
FACTORY DEFAULT:
(blank)