Singer One Instruction Manual 14 - Page 82
Replacing, Slide, Plate, Changing, Light, place, plaque, glissiere, l'ampoule, Reponer, Plancha,
View all Singer One manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 82 highlights
r 2 3 .Tc Replacing the Slide Plate You will not have any occasion to remove the slide plate. However, if it should accidentally become disengaged from the machine, it is easily replaced. • Raise the presser foot and make sure needle is in its highest position. • Place slide plate in slide way a with the front edge close to, but not covering, the retaining spring b. • With a small screwdriver, lift each end of the spring into each of the side grooves on the underside of the plate. • Draw the plate gently toward you and fully engage the spring. • Close slide plate. Changing the Light Bulb CAUTION: Before changing light bulb make sure you have disconnected the power line plug from the socket outlet. This machine is designed to use a 15 watt maximum bayonet base bulb only. Removing Bulb 1. To lower the light bracket, push in and down on tab c. 2. Do not attempt to unscrew the bulb. Press it up into the socket and at the same time turn bulb over in direction shown to unlock the bulb pin d. Replacing Bulb 3. Press new bulb into socket, with bulb pin d entering slot of socket e, and turn it over in direction shown to lock bulb in position. Push entire assembly up until it snaps in position. Mise en place de la plaque glissiere Vous n'aurez pas normalement a demonter la plaque glissiere. Cependant, si accidentellement celle-ci se deboite, sa remise en place est tres facile. • Levez le pied presseur et assurez-vous que l'aiguille est en position haute. • Presentez la plaque glissiere comme illustre, elle ne dolt pas recouvrir le ressort de fixation b. • A l'aide d'un petit tournevis, levez l'une apres l'autre les extremites du ressort b et glissez les dans les rainures a de la plaque glissiere. • Poussez la plaque doucement vers vous pour engager a fond le ressort. • Fermez la plaque glissiere. Mise en place de l'ampoule ATTENTION: Avant de changer l'ampoule, debranchez votre machine. N'utilisez que des ampoules de 15 watts maximum. Pour retirer l'ampoule: 1. Pour abaisser le support lampe, appuyez sur la patte c. 2. N'essayez pas de devisser l'ampoule. Poussez la dans son logement et en meme temps, tournez dans le sens indique sur l'illustration pour la degager. Remise en place: 3. Placez la nouvelle ampoule dans son logement, les baIonnettes d face aux encoches e. Poussez et tournez dans le sens illustre. Remontez le tout. Como Reponer la Plancha Deslizante Usted no tendra ninguna ocasi0n de sacar la plancha deslizante. Sin embargo, en caso de que debido a un accidente se desenganchara de la maquina, es facil de reponer. • Levante el prensatelas y asegurese de que la aguja esta en su mas alta posici0n. • Coloque la plancha deslizante en el camino corredizo a con el borde frontal cerca de, pero sin cubrir, el muelle de retenci6n b. • Con un destornillador pequeno, levante cada extremo del muelle dentro de cada una de las ranuras de la parte inferior de la plancha. • Traiga la plancha suavemente hacia usted y encaje el muelle por completo. • Cierre la plancha deslizante. C6mo Cambiar la BombNla C. UID,ADO: Antes de cambiar la bombilla asegurese de que ha desconectado el enchufe macho de la linea electrica del enchufe hembra de salida. Esta maquina esta diserfada para usar una bombilla de casquillo de bayoneta de 15 vatios maximo solamente. Como Sacar la Bombilla 1. Para bajar la abrazadera de luz, apriete hacia adentro y hacia abajo en la orejeta c. 2. No intente destornillar la bombilla. Empujela en el receptaculo y al mismo tiempo girela en el sentido que se indica para desenclavar el pasador de la bombilla d. Como Reponer la Bombilla 3. Ponga la bombilla nueva en el receptaculo e, con el pasador d insertado en este ygire en el sentido que se muestra para que la bombilla quede en posici0n. Empuje todo el conjunto hacia arriba hastaque caiga en posici6n. 81