Yamaha CLP-480 Owner's Manual - Page 85

Attach C., Connect the power cord., Set the adjuster., Attach the headphone hanger

Page 85 highlights

Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly. WARNING An improper voltage setting can cause serious damage to the instrument or result in improper operation. 8-2 Insert the plug of the power cord into the power connector. 7. Attach C. 7-1 Place on D, the stopper-wood at the bottom edges of C, then secure the top. 7-2 Secure the upper right, left, and center parts of C using three 4 x 14 mm thin screws. 7-3 Secure the lower part of C using four 4 x 20 mm tapping screws. 7-2 8-1 8-2 240 220 110 127 9. Set the adjuster. Rotate the adjuster until the pedal box comes in firm contact with the floor surface. 7-1 C D C 7-3 8. Connect the power cord. 8-1 For models that feature a voltage selector: Set the voltage selector to an appropriate voltage. Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a "minus" screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC IN and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area. 10. Attach the headphone hanger. Use the included two screws (4 x 10 mm) to attach the hanger as shown in the illustration. Appendix 85 Assembling the Clavinova

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96

85
Appendix
Assembling the Clavinova
7.
Attach C.
7-1
Place on D, the stopper-wood at the bottom
edges of C, then secure the top.
7-2
Secure the upper right, left, and center parts
of C using three 4 x 14 mm thin screws.
7-3
Secure the lower part of C using four 4 x 20
mm tapping screws.
8.
Connect the power cord.
8-1
For models that feature a voltage selector:
Set the voltage selector to an appropriate
voltage.
WARNING
An improper voltage setting can cause serious damage to the
instrument or result in improper operation.
8-2
Insert the plug of the power cord into the
power connector.
9.
Set the adjuster.
Rotate the adjuster until the pedal box comes in
firm contact with the floor surface.
10.
Attach the headphone hanger.
Use the included two screws (4 x 10 mm) to attach
the hanger as shown in the illustration.
Insert the pedal cord securely
until the metal part of the cord
plug disappears from view.
Otherwise, the pedal may not
function properly.
Voltage Selector
Before connecting the AC power cord, check the
setting of the voltage selector which is provided in
some areas. To set the selector for 110V, 127V, 220V
or 240V main voltages, use a “minus” screwdriver to
rotate the selector dial so that the correct voltage for
your region appears next to the pointer on the panel.
The voltage selector is set at 240V when the unit is
initially shipped. After the proper voltage has been
selected, connect the AC power cord to the AC IN
and an AC wall outlet. A plug adaptor may be also
provided in some areas to match the pin
configuration of the AC wall outlets in your area.
C
D
C
7-1
7-2
7-3
240
127
110
220
8-2
8-1