Home » ZyXEL Manuals » Networking » ZyXEL P-2812HNU-F1 » Manual Viewer

ZyXEL P-2812HNU-F1 User Guide - Page 109

Table 11, Label, Description

Get ZyXEL P-2812HNU-F1 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Chapter 5 Broadband Table 11 Broadband Add/Edit: Routing- IPoE (ADSL) (continued) LABEL DESCRIPTION IPv6/IPv4 DualStack Select Enable to allow the Device to run IPv4 and IPv6 at the same time. If this function is disabled, the Device only runs IPv4. ATM PVC Configuration VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. VPI VCI DSL Link Type Encapsulation Mode This section is available only when you select ADSL in the Type field to configure an ATM layer-2 interface. The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Enter the VCI assigned to you. The DSL link type is set to EoA (Ethernet over ATM) to have an Ethernet header in the packet, so that you can have multiple services/connections over one PVC. You can set each connection to have its own MAC address or all connections share one MAC address but use different VLAN IDs for different services. EoA supports IPoE, PPPoE and RFC1483/2684 bridging encapsulation methods. Select the method of multiplexing used by your ISP from the drop-down list. Choices are: Service Category • LLC/SNAP-BRIDGING In LCC encapsulation, bridged PDUs are encapsulated by identifying the type of the bridged media in the SNAP header. This is available only when the DSL Link Type is set to EoA. • VC/MUX: In VC multiplexing, each protocol is carried on a single ATM virtual circuit (VC). To transport multiple protocols, the Device needs separate VCs. There is a binding between a VC and the type of the network protocol carried on the VC. This reduces payload overhead since there is no need to carry protocol information in each Protocol Data Unit (PDU) payload. Select UBR Without PCR for applications that are non-time sensitive, such as e-mail. Select CBR (Constant Bit Rate) to specify fixed (always-on) bandwidth for voice or data traffic. Select Non Realtime VBR (non real-time Variable Bit Rate) for connections that do not require closely controlled delay and delay variation. Peak Cell Rate Select Realtime VBR (real-time Variable Bit Rate) for applications with bursty connections that require closely controlled delay and delay variation. Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak Cell Rate (PCR). This is the maximum rate at which the sender can send cells. Type the PCR here. Sustainable Cell Rate This field is not available when you select UBR Without PCR. The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be transmitted. Type the SCR, which must be less than the PCR. Note that system default is 0 cells/sec. Maximum Burst Size This field is available only when you select Non Realtime VBR or Realtime VBR. Maximum Burst Size (MBS) refers to the maximum number of cells that can be sent at the peak rate. Type the MBS, which is less than 65535. IP Address This field is available only when you select Non Realtime VBR or Realtime VBR. This section is available only when you select Routing in the Mode field and IPoE in the WAN Service Type field. P-2812HNU(L)-Fx Series User's Guide 109

Section	Page
P-2812HNU(L)-Fx Series	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
User’s Guide	19
Introduction	21
1.1 Overview	21
1.2 Applications for the Device	21
1.2.1 Internet Access	21
1.2.2 VoIP Features	22
1.2.3 Wireless Connection	22
1.3 The WLAN Button	23
1.4 Ways to Manage the Device	24
1.5 Good Habits for Managing the Device	24
1.6 LEDs (Lights)	24
1.7 The RESET Button	26
Introducing the Web Configurator	27
2.1 Overview	27
2.1.1 Accessing the Web Configurator	27
2.2 The Web Configurator Layout	29
2.2.1 Title Bar	29
2.2.2 Main Window	29
2.2.3 Navigation Panel	30
Tutorials	33
3.1 Overview	33
3.2 Setting Up Your DSL Connection	33
3.3 How to Set up a Wireless Network	36
3.3.1 Example Parameters	36
3.3.2 Configuring the AP	36
3.3.3 Configuring the Wireless Client	38
3.4 Setting Up NAT Port Forwarding	43
3.5 How to Make a VoIP Call	44
3.5.1 VoIP Calls With a Registered SIP Account	45
3.6 Using the File Sharing Feature	47
3.6.1 Set Up File Sharing	48
3.6.2 Access Your Shared Files From a Computer	49
3.7 Using the Media Server Feature	49
3.7.1 Configuring the Device	50
3.7.2 Using Windows Media Player	50
3.7.3 Using a Digital Media Adapter	53
3.8 Using the Print Server Feature	55
3.9 Configuring the MAC Address Filter	70
3.10 Configuring Static Route for Routing to Another Network	71
3.11 Configuring QoS Queue and Class Setup	73
3.12 Access the Device Using DDNS	76
3.12.1 Registering a DDNS Account on www.dyndns.org	77
3.12.2 Configuring DDNS on Your Device	77
3.12.3 Testing the DDNS Setting	77
Technical Reference	79
Connection Status and System Info	81
4.1 Overview	81
4.2 The Connection Status Screen	81
4.3 The System Info Screen	83
Broadband	87
5.1 Overview	87
5.1.1 What You Can Do in this Chapter	88
5.1.2 What You Need to Know	88
5.1.3 Before You Begin	91
5.2 The Broadband Screen	91
5.2.1 Add/Edit Internet Connection	93
5.3 The 3G Backup Screen	115
5.4 Technical Reference	117
Wireless	123
6.1 Overview	123
6.1.1 What You Can Do in this Chapter	123
6.1.2 Wireless Network Overview	123
6.1.3 Before You Begin	125
6.2 The Wireless General Screen	125
6.2.1 No Security	127
6.2.2 Basic (Static WEP/Shared WEP Encryption)	127
6.2.3 More Secure (WPA(2)-PSK)	129
6.2.4 WPA(2) Authentication	130
6.3 The More AP Screen	131
6.3.1 Edit More AP	132
6.4 The WPS Screen	133
6.5 The WMM Screen	135
6.6 Scheduling Screen	137
6.7 Technical Reference	137
6.7.1 Additional Wireless Terms	138
6.7.2 Wireless Security Overview	138
6.7.3 Signal Problems	140
6.7.4 BSS	141
6.7.5 MBSSID	141
6.7.6 WiFi Protected Setup (WPS)	142
Home Networking	149
7.1 Overview	149
7.1.1 What You Can Do in this Chapter	149
7.1.2 What You Need To Know	149
7.2 The LAN Setup Screen	152
7.3 The Static DHCP Screen	153
7.3.1 Before You Begin	153
7.4 The UPnP Screen	155
7.5 The File Sharing Screen	155
7.5.1 Before You Begin	156
7.5.2 Add/Edit File Sharing	157
7.6 The Media Server Screen	158
7.7 The Printer Server Screen	159
7.7.1 Before You Begin	159
7.8 Technical Reference	160
7.9 Installing UPnP in Windows Example	164
7.10 Using UPnP in Windows XP Example	167
Routing	173
8.1 Overview	173
8.2 Configuring Static Route	174
8.2.1 Add/Edit Static Route	175
Quality of Service (QoS)	177
9.1 Overview	177
9.1.1 What You Can Do in this Chapter	177
9.1.2 What You Need to Know	177
9.2 The QoS General Screen	178
9.3 The Queue Setup Screen	180
9.3.1 Add/Edit a QoS Queue	181
9.4 The Class Setup Screen	181
9.4.1 Add/Edit QoS Class	183
9.5 The QoS Monitor Screen	186
9.6 QoS Technical Reference	187
9.6.1 IEEE 802.1Q Tag	187
9.6.2 IP Precedence	187
9.6.3 DiffServ	187
Network Address Translation (NAT)	189
10.1 Overview	189
10.1.1 What You Can Do in this Chapter	189
10.1.2 What You Need To Know	189
10.2 The Port Forwarding Screen	190
10.2.1 The Port Forwarding Screen	190
10.2.2 The Port Forwarding Edit Screen	192
10.3 The Sessions Screen	193
10.4 Technical Reference	193
10.4.1 NAT Definitions	193
10.4.2 What NAT Does	194
10.4.3 How NAT Works	194
Dynamic DNS	197
11.1 Overview	197
11.1.1 What You Need To Know	197
11.2 The Dynamic DNS Screen	197
Firewall	199
12.1 Overview	199
12.1.1 What You Can Do in this Chapter	199
12.1.2 What You Need to Know	199
12.2 The General Screen	200
12.3 The Services Screen	201
12.4 Firewall Technical Reference	202
12.4.1 Guidelines For Enhancing Security With Your Firewall	202
12.4.2 Security Considerations	202
MAC Filter	205
13.1 Overview	205
13.1.1 What You Need to Know	205
13.2 The MAC Filter Screen	205
Parental Control	207
14.1 Overview	207
14.2 The Parental Control Screen	207
14.2.1 Add/Edit a Parental Control Rule	208
Certificates	211
15.1 Overview	211
15.1.1 What You Can Do in this Chapter	211
15.1.2 What You Need to Know	211
15.1.3 Verifying a Certificate	212
15.2 Local Certificates	213
15.3 Trusted CA	215
15.4 Trusted CA Import	215
15.5 View Certificate	216
VoIP	219
16.1 Overview	219
16.1.1 What You Can Do in this Chapter	219
16.1.2 What You Need to Know	219
16.1.3 Before You Begin	221
16.2 The SIP Service Provider Screen	221
16.3 The SIP Account Screen	224
16.3.1 Add/Edit SIP Account	226
16.4 Multiple SIP Accounts	228
16.5 The Common Screen	228
16.6 Phone Screen	229
16.6.1 Edit Phone Device	230
16.7 The Phone Region Screen	231
16.8 The Call Rule Screen	231
16.9 The FXO Screen (“L” Models Only)	233
16.10 Technical Reference	233
16.10.1 VoIP	234
16.10.2 SIP	234
16.10.3 Quality of Service (QoS)	238
16.10.4 Phone Services Overview	239
Logs	243
17.1 Overview	243
17.1.1 What You Can Do in this Chapter	243
17.1.2 What You Need To Know	243
17.2 The System Log Screen	244
17.3 The Phone Log Screen	245
17.4 The VoIP Call History Screen	245
Traffic Status	247
18.1 Overview	247
18.1.1 What You Can Do in this Chapter	247
18.2 The WAN Status Screen	247
18.3 The LAN Status Screen	248
18.4 The NAT Status Screen	249
18.5 The 3G Backup Status Screen	250
18.6 The VoIP Status Screen	251
User Account	253
19.1 Overview	253
19.2 The User Account Screen	253
Remote MGMT	255
20.1 Overview	255
20.1.1 What You Need to Know	255
20.2 The Remote MGMT Screen	256
System	257
21.1 Overview	257
21.1.1 What You Need to Know	257
21.2 The System Screen	257
Time Setting	259
22.1 Overview	259
22.2 The Time Setting Screen	259
Log Setting	261
23.1 Overview	261
23.2 The Log Setting Screen	261
Firmware Upgrade	263
24.1 Overview	263
24.2 The Firmware Upgrade Screen	263
Backup/Restore	265
25.1 Overview	265
25.2 The Backup/Restore Screen	265
25.3 The Reboot Screen	267
Diagnostic	269
26.1 Overview	269
26.2 The Ping/TraceRoute Screen	269
26.3 The DSL Line Screen	270
Troubleshooting	273
27.1 Overview	273
27.2 Power, Hardware Connections, and LEDs	273
27.3 Device Access and Login	274
27.4 Internet Access	276
27.5 Wireless Internet Access	278
27.6 Phone Calls and VoIP	279
27.7 USB Device Connection	279
27.8 UPnP	279
Product Specifications	281
IP Addresses and Subnetting	289
Setting Up Your Computer’s IP Address	299
Pop-up Windows, JavaScript and Java Permissions	329
Wireless LANs	339
Common Services	359
IPv6	363
Open Software Announcements	375
Legal Information	411

Match case Limit results 1 per page

Chapter 5 Broadband

P-2812HNU(L)-Fx Series User’s Guide

109

IPv6/IPv4

DualStack

Select

Enable

to allow the Device to run IPv4 and IPv6 at the same time. If

this function is disabled, the Device only runs IPv4.

ATM PVC

Configuration

VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual

circuit.

This section is available only when you select

ADSL

in the

Type

field to

configure an ATM layer-2 interface.

VPI

The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.

VCI

The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local

management of ATM traffic). Enter the VCI assigned to you.

DSL Link Type

The DSL link type is set to

EoA

(Ethernet over ATM) to have an Ethernet

header in the packet, so that you can have multiple services/connections over

one PVC. You can set each connection to have its own MAC address or all

connections share one MAC address but use different VLAN IDs for different

services.

EoA

supports IPoE, PPPoE and RFC1483/2684 bridging encapsulation

methods.

Encapsulation

Mode

Select the method of multiplexing used by your ISP from the drop-down list.

Choices are:

•

LLC/SNAP-BRIDGING

In LCC encapsulation, bridged PDUs are

encapsulated by identifying the type of the bridged media in the SNAP

header. This is available only when the

DSL Link Type

is set to

EoA

•

VC/MUX:

In VC multiplexing, each protocol is carried on a single ATM

virtual circuit (VC). To transport multiple protocols, the Device needs

separate VCs. There is a binding between a VC and the type of the network

protocol carried on the VC. This reduces payload overhead since there is no

need to carry protocol information in each Protocol Data Unit (PDU)

payload.

Service Category

Select

UBR Without PCR

for applications that are non-time sensitive, such as

e-mail.

Select

CBR

(Constant Bit Rate) to specify fixed (always-on) bandwidth for voice

or data traffic.

Select

Non Realtime VBR

(non real-time Variable Bit Rate) for connections

that do not require closely controlled delay and delay variation.

Select

Realtime VBR

(real-time Variable Bit Rate) for applications with bursty

connections that require closely controlled delay and delay variation.

Peak Cell Rate

Divide the DSL line rate (bps) by 424 (the size of an ATM cell) to find the Peak

Cell Rate (PCR). This is the maximum rate at which the sender can send cells.

Type the PCR here.

This field is not available when you select

UBR Without PCR

Sustainable Cell

Rate

The Sustain Cell Rate (SCR) sets the average cell rate (long-term) that can be

transmitted. Type the SCR, which must be less than the PCR. Note that system

default is 0 cells/sec.

This field is available only when you select

Non Realtime VBR

Realtime

VBR

Maximum Burst

Size

Maximum Burst Size (MBS) refers to the maximum number of cells that can be

sent at the peak rate. Type the MBS, which is less than 65535.

This field is available only when you select

Non Realtime VBR

Realtime

VBR

IP Address

This section is available only when you select

Routing

in the

Mode

field and

IPoE

in the

WAN Service Type

field.

Table 11

Broadband Add/Edit: Routing- IPoE (ADSL) (continued)

LABEL

DESCRIPTION