Dell Broadcom NetXtreme Family of Adapters Broadcom NetXtreme II Network Adapt - Page 68

iSCSI Boot Configuration, TCP/IP parameters via DHCP

Get Dell Broadcom NetXtreme Family of Adapters PDF manuals and user guides View all Dell Broadcom NetXtreme Family of Adapters manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

iSCSI Protocol: Broadcom NetXtreme II Network Adapter User Guide 3. From the MBA Configuration Menu, use the UP ARROW or DOWN ARROW to move to the Boot Protocol option. Use the LEFT ARROW or RIGHT ARROW to change the Boot Protocol option to iSCSI. NOTE: For iSCSI boot-capable LOMs, the boot protocol is set via the BIOS. See your system documentation for more information. 4. Select iSCSI Boot Configuration from Main Menu. NOTE: If iSCSI boot firmware is not programmed in the NetXtreme II network adapter, selecting iSCSI Boot Configuration will not have any effect. iSCSI Boot Configuration Static iSCSI Boot Configuration Dynamic iSCSI Boot Configuration Static iSCSI Boot Configuration In a static configuration, you must enter data for the system's IP address, the system's initiator IQN, and the target parameters obtained in Configuring the iSCSI Target. For information on configuration options, see Table 1. To configure the iSCSI boot parameters using static configuration 1. From the General Parameters Menu screen, set the following: TCP/IP parameters via DHCP: Disabled. (For IPv4.) IP Autoconfiguration: Disabled. (For IPv6, non-offload.) iSCSI parameters via DHCP: Disabled CHAP Authentication: Disabled Boot to iSCSI target: Disabled DHCP Vendor ID: BRCM ISAN Link Up Delay Time: 0 Use TCP Timestamp: Enabled (for some targets such as the Dell/EMC AX100i, it is necessary to enable Use TCP Timestamp) Target as First HDD: Disabled LUN Busy Retry Count: 0 IP Version: IPv6. (For IPv6, non-offload.) HBA Boot Mode: Disabled 2. Select ESC to return to the Main menu. 3. From the Main menu, select Initiator Parameters. 4. From the Initiator Parameters screen, type values for the following: IP Address (unspecified IPv4 and IPv6 addresses should be "0.0.0.0" and "::", respectively) Subnet Mask Prefix Default Gateway Primary DNS Secondary DNS iSCSI Name (corresponds to the iSCSI initiator name to be used by the client system) NOTE: Carefully enter the IP address. There is no error-checking performed against the IP address to check for duplicates or incorrect segment/network assignment. 5. Select ESC to return to the Main menu. 6. From the Main menu, select 1st Target Parameters. NOTE: For the initial setup, configuring a second target is not supported. 7. From the 1st Target Parameters screen, enable Connect to connect to the iSCSI target. Type values for the file:///T|/htdocs/NETWORK/BroadCom/71921/NetXtremeII/en/iscsi.htm[9/26/2012 3:29:03 PM]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
iSCSI Protocol: Broadcom NetXtreme II Network Adapter User Guide
file:///T|/htdocs/NETWORK/BroadCom/71921/NetXtremeII/en/iscsi.htm[9/26/2012 3:29:03 PM]
3. From the MBA Configuration Menu, use the
UP ARROW
or
DOWN ARROW
to move to the
Boot Protocol
option. Use
the
LEFT ARROW
or
RIGHT ARROW
to change the
Boot Protocol
option to
iSCSI
.
NOTE: For iSCSI boot-capable LOMs, the boot protocol is set via the BIOS. See your system documentation for
more information.
4. Select
iSCSI Boot Configuration
from
Main Menu
.
NOTE: If iSCSI boot firmware is not programmed in the NetXtreme II network adapter, selecting
iSCSI Boot
Configuration
will not have any effect.
iSCSI Boot Configuration
Static iSCSI Boot Configuration
Dynamic iSCSI Boot Configuration
Static iSCSI Boot Configuration
In a static configuration, you must enter data for the system's IP address, the system's initiator IQN, and the target
parameters obtained in
Configuring the iSCSI Target
. For information on configuration options, see
Table 1
.
To configure the iSCSI boot parameters using static configuration
1. From the
General Parameters Menu
screen, set the following:
TCP/IP parameters via DHCP
: Disabled. (For IPv4.)
IP Autoconfiguration
: Disabled. (For IPv6, non-offload.)
iSCSI parameters via DHCP
: Disabled
CHAP Authentication
: Disabled
Boot to iSCSI target
: Disabled
DHCP Vendor ID
: BRCM ISAN
Link Up Delay Time
: 0
Use TCP Timestamp
: Enabled (for some targets such as the Dell/EMC AX100i, it is necessary to enable
Use
TCP Timestamp
)
Target as First HDD
: Disabled
LUN Busy Retry Count
: 0
IP Version
: IPv6. (For IPv6, non-offload.)
HBA Boot Mode
: Disabled
2. Select
ESC
to return to the
Main
menu.
3. From the
Main
menu, select
Initiator Parameters
.
4. From the
Initiator Parameters
screen, type values for the following:
IP Address (unspecified IPv4 and IPv6 addresses should be "0.0.0.0" and "::", respectively
)
Subnet Mask Prefix
Default Gateway
Primary DNS
Secondary DNS
iSCSI Name (corresponds to the iSCSI initiator name to be used by the client system)
NOTE: Carefully enter the IP address. There is no error-checking performed against the IP address to check
for duplicates or incorrect segment/network assignment.
5. Select
ESC
to return to the
Main
menu.
6. From the
Main
menu, select
1st Target Parameters
.
NOTE: For the initial setup, configuring a second target is not supported.
7. From the
1st Target Parameters
screen, enable
Connect
to connect to the iSCSI target. Type values for the