Dell DX6000G Hardware Owner's Manual - Page 104

Removing an iDRAC6 Enterprise Card, card. See Integrated Dell Remote Access Controller 6 Express Card

Get Dell DX6000G PDF manuals and user guides View all Dell DX6000G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Removing an iDRAC6 Enterprise Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 If present, disconnect the Ethernet cable from the iDRAC6 enterprise card connector on the system back panel. See Figure 1-4. 3 Open the system. See "Opening the System" on page 80. 4 Remove the system board shroud. See "Removing the System Board Shroud" on page 98. 5 Remove the VFlash media card (if installed) from the iDRAC6 enterprise card. See "Integrated Dell Remote Access Controller 6 Express Card (Optional)" on page 100. 6 Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs. 7 As the card releases from the standoffs, the connector under the card disengages from the system board connector. 8 Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system. 9 Replace the plastic filler plug over the port at the system back panel. See "Back-Panel Features and Indicators" on page 17 for the port location. 10 Replace the system board shroud. See "Installing the System Board Shroud" on page 99. 11 Close the system. See "Closing the System" on page 81. 12 Reconnect the system and peripherals to their power sources, and turn them on. 104 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
104
Installing System Components
Removing an iDRAC6 Enterprise Card
CAUTION:
Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
If present, disconnect the Ethernet cable from the iDRAC6 enterprise card
connector on the system back panel. See Figure 1-4.
3
Open the system. See "Opening the System" on page 80.
4
Remove the system board shroud. See "Removing the System Board
Shroud" on page 98.
5
Remove the VFlash media card (if installed) from the iDRAC6 enterprise
card. See "Integrated Dell Remote Access Controller 6 Express Card
(Optional)" on page 100.
6
Pull back slightly on the two tabs at the front edge of the card and gently
lift the front edge of the card off of the retention standoffs.
7
As the card releases from the standoffs, the connector under the card
disengages from the system board connector.
8
Slide the card away from the back of the system until the RJ-45 connector
is clear of the back panel, then lift the card out of the system.
9
Replace the plastic filler plug over the port at the system back panel.
See "Back-Panel Features and Indicators" on page 17 for the port location.
10
Replace the system board shroud. See "Installing the System Board
Shroud" on page 99.
11
Close the system. See "Closing the System" on page 81.
12
Reconnect the system and peripherals to their power sources, and turn
them on.