Dell DX6000G Hardware Owner's Manual - Page 48

Unsupported CPU, Integrated, Dell™ Remote, Access Controller 6, iDRAC6 User Guide

Get Dell DX6000G PDF manuals and user guides View all Dell DX6000G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Table 1-2. System Messages (continued) Message Causes Corrective Actions Unable to launch System Services image. System halted! System halted after pressing Restart the system and because System update the Unified Server Services image is either Configurator repository to corrupted in the system the latest software to restore firmware or has been lost due full functionality. See the to system board replacement. Unified Server The optional iDRAC6 Enterprise card flash memory or BMC SPI flash may be Configuration user documentation for more information. corrupted. Restore the flash memory using the latest version on support.dell.com. See the Integrated Dell™ Remote Access Controller 6 (iDRAC6) User Guide for instructions on performing a field replacement of the flash memory. Unexpected interrupt in protected mode Improperly seated memory modules or faulty keyboard/mouse controller chip. Reseat the memory modules. See "Troubleshooting System Memory" on page 148. If the problem persists, see "Getting Help" on page 169. Unsupported CPU combination Unsupported CPU stepping detected Processor(s) not supported by the system. Install a supported processor or processor combination. See "Processors" on page 118. Unsupported DIMM detected. The following DIMM has been disabled: x Invalid memory configuration. The system will run but with the specified memory module disabled. Ensure that the memory modules are installed in a valid configuration. See "General Memory Module Installation Guidelines" on page 111. 48 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
48
About Your System
Unable to launch
System Services
image. System
halted!
System halted after pressing
<F10> because System
Services image is either
corrupted in the system
firmware or has been lost due
to system board replacement.
The optional iDRAC6
Enterprise card flash memory
or BMC SPI flash may be
corrupted.
Restart the system and
update the Unified Server
Configurator repository to
the latest software to restore
full functionality. See the
Unified Server
Configuration user
documentation for
more information.
Restore the flash memory
using the latest version on
support.dell.com. See the
Integrated
Dell™ Remote
Access Controller 6
(iDRAC6) User Guide
for
instructions on performing a
field replacement of the
flash memory.
Unexpected
interrupt in
protected mode
Improperly seated memory
modules or faulty
keyboard/mouse
controller chip.
Reseat the memory modules.
See "Troubleshooting
System Memory" on
page 148. If the problem
persists, see "Getting Help"
on page 169.
Unsupported CPU
combination
Unsupported CPU
stepping
detected
Processor(s) not supported
by the system.
Install a supported processor
or processor combination.
See "Processors" on
page 118.
Unsupported DIMM
detected. The
following DIMM
has been
disabled:
x
Invalid memory
configuration. The system
will run but with the
specified memory module
disabled.
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines" on
page 111.
Table 1-2.
System Messages
(continued)
Message
Causes
Corrective Actions