Dell PowerEdge 1955 Hardware Owner's Manual (PDF) - Page 36

Error: Incorrect memory, System Setup Program - dimm

Get Dell PowerEdge 1955 PDF manuals and user guides View all Dell PowerEdge 1955 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Table 1-13. Server Module Messages (continued) Message Causes Corrective Actions DIMMs must be populated in sequential order beginning with slot 1. The following DIMM is electrically isolated: DIMM x. The specified DIMM is inaccessible to Populate two, four, or eight DIMMs the system due to its location. sequentially beginning with slot 1. DIMMs must be populated in sequential order, beginning with slot 1. DIMM pairs must be matched in size, speed, and technology. The following DIMM pair is mismatched: DIMM x and DIMM y. Mismatched or unmatched DIMMs installed; faulty or improperly seated memory modules. Ensure that all pairs of memory modules are of the same type and size, and that they are properly installed. See "General Memory Module Installation Guidelines" on page 78. See "Troubleshooting Server Module Memory" on page 112. Diskette drive n seek failure Incorrect configuration settings in System Setup program. Run the System Setup program to correct the settings. See "Using the System Setup Program" on page 43. Faulty or improperly connected Replace the diskette. Ensure that the diskette or optical drive to the custom diskette drive and optical drive cables are cable. properly connected. See "Troubleshooting USB Devices" on page 105. Diskette read failure Faulty or improperly inserted diskette. Replace the diskette. Diskette subsystem reset failed Faulty diskette drive or optical drive controller. Ensure that the diskette drive and optical drive cables are properly connected to the custom cable. See "Troubleshooting USB Devices" on page 105. If the problem persists, see "Getting Help" on page 127. Drive not ready Diskette missing or improperly inserted in diskette drive. Reinsert or replace the diskette. Error: Incorrect memory configuration. DIMMs must be installed in pairs of matched memory size, speed, and technology. Mismatched or unmatched DIMMs installed; faulty or improperly seated memory modules. Ensure that all pairs of memory modules are of the same type and size, and that they are properly installed. See "General Memory Module Installation Guidelines" on page 78. If the problem persists, see "Troubleshooting Server Module Memory" on page 112. 36 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
36
About Your System
DIMMs must be populated in
sequential order beginning
with slot 1. The following
DIMM is electrically
isolated: DIMM
x
.
The specified DIMM is inaccessible to
the system due to its location.
DIMMs must be populated in
sequential order, beginning with
slot 1.
Populate two, four, or eight DIMMs
sequentially beginning with slot 1.
DIMM pairs must be matched
in size, speed, and
technology. The following
DIMM pair is mismatched:
DIMM
x
and DIMM
y.
Mismatched or unmatched DIMMs
installed; faulty or improperly seated
memory modules.
Ensure that all pairs of memory modules
are of the same type and size, and that
they are properly installed. See "General
Memory Module Installation
Guidelines" on page 78. See
"Troubleshooting Server Module
Memory" on page 112.
Diskette drive
n
seek
failure
Incorrect configuration settings in
System Setup program.
Run the System Setup program to
correct the settings. See "Using the
System Setup Program" on page 43.
Faulty or improperly connected
diskette or optical drive to the custom
cable.
Replace the diskette. Ensure that the
diskette drive and optical drive cables are
properly connected. See
"Troubleshooting USB Devices" on
page 105.
Diskette read failure
Faulty or improperly inserted diskette.
Replace the diskette.
Diskette subsystem reset
failed
Faulty diskette drive or optical drive
controller.
Ensure that the diskette drive and
optical drive cables are properly
connected to the custom cable. See
"Troubleshooting USB Devices" on
page 105. If the problem persists, see
"Getting Help" on page 127.
Drive not ready
Diskette missing or improperly
inserted in diskette drive.
Reinsert or replace the diskette.
Error: Incorrect memory
configuration. DIMMs must
be installed in pairs of
matched memory size,
speed, and technology.
Mismatched or unmatched DIMMs
installed; faulty or improperly seated
memory modules.
Ensure that all pairs of memory modules
are of the same type and size, and that
they are properly installed. See "General
Memory Module Installation
Guidelines" on page 78. If the problem
persists, see "Troubleshooting Server
Module Memory" on page 112.
Table 1-13.
Server Module Messages
(continued)
Message
Causes
Corrective Actions