Fujitsu 5900C Operator's Guide

Fujitsu 5900C - fi - Document Scanner Manual

Get Fujitsu 5900C - fi - Document Scanner PDF manuals and user guides
UPC - 097564306945
View all Fujitsu 5900C manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu 5900C manual content summary:

  • Fujitsu 5900C | Operator's Guide - Page 1
    P3PC-1432-02ENZ0 fi-5900C Image Scanner Operator's Guide Function Hopper Hegiht Thin Power Thickness Thick Send to Scan
  • Fujitsu 5900C | Operator's Guide - Page 2
  • Fujitsu 5900C | Operator's Guide - Page 3
    INTRODUCTION Thank you for purchasing the fi-5900C Image Scanner. The fi-5900C is an image scanner designed to scan various documents in large quantities. The fi-5900C has the following features. Improvement of color scanning speed (100 sheets or 200 pages per minute) with high resolution (300dpi)
  • Fujitsu 5900C | Operator's Guide - Page 4
    be done for the scanner using the Software Operation Panel. 9. OPTIONS This chapter describes the options available for this product. 10. SCANNER SPECIFICATIONS This chapter lists the scanner specifications. The "Getting Started" is supplied to this Scanner. This guide contains necessary information
  • Fujitsu 5900C | Operator's Guide - Page 5
    describes how to prepare the scanner for use. 2. INSTALLATION OF THE SCANNER This chapter describes how to install and connect the scanner, and how to install the scanner application. We hope that this manual is useful in taking full advantage of the fi-5900C Duplex Color Scanner's features. iii
  • Fujitsu 5900C | Operator's Guide - Page 6
    to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
  • Fujitsu 5900C | Operator's Guide - Page 7
    fi-5900C traffic control, operation control in mass third party. About the use of mercury Hg Lamp(s) inside this product contain lamp in your mouth as it has mercury. •Do not breathe the chemical liquid contained in the scanner lamps. •Do not incinerate, crush, or shred the lamps or scanner parts
  • Fujitsu 5900C | Operator's Guide - Page 8
    Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. ISIS, QuickScan of the above operating system, the general term "Windows "is used. Adobe Acrobat Adobe® Acrobat® All the descriptions in this manual assume the usage
  • Fujitsu 5900C | Operator's Guide - Page 9
    understand the Safety Precautions described in this manual before you use this product. Warning Indications Used In This Manual This manual uses the following indications to ensure safe and correct use of this product, and to prevent possible danger and injury to the Operator and other persons. vii
  • Fujitsu 5900C | Operator's Guide - Page 10
    operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment. Symbols Used In This Manual This manual uses shows the specific action that is not allowed. R Outline characters on a colored background show instructions users should
  • Fujitsu 5900C | Operator's Guide - Page 11
    manual, operate by following the actual displayed screen while referring to the User's Manual of the scanner application you are using. Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner driver
  • Fujitsu 5900C | Operator's Guide - Page 12
    WARNING The following describes important warnings described in this manual. Do not touch the Power cable with wet hands do not use the AC cable provided with this scanner for other devices, since this might cause equipment failure and other troubles or an electric shock. Use this scanner only
  • Fujitsu 5900C | Operator's Guide - Page 13
    detect other problems such as smoke, strange smells or noises, immediately turn off the scanner and disconnect its power plug. Make sure that the smoking has stopped, and then contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. Turn the scanner OFF if
  • Fujitsu 5900C | Operator's Guide - Page 14
    manual. Do not install the scanner on unstable surfaces. Install the scanner on a desk so that none of its parts protrude outside of the desktop. Also, make sure that the scanner from tilting. Install the scanner on a strong surface that will support the weight of the scanner and any other devices on
  • Fujitsu 5900C | Operator's Guide - Page 15
    . Do not use aerosol sprays near the scanner. Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt and dust to enter the scanner, resulting in scanner failure and malfunction. Avoid any contact when the scanner is in use. Avoid touching any part of the scanner mechanism or paper
  • Fujitsu 5900C | Operator's Guide - Page 16
    for safety. Do not install the scanner in the direct sunlight. Do not install the scanner in the direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, causing fire or scanner trouble. Install the scanner in a well-ventilated location. Do not
  • Fujitsu 5900C | Operator's Guide - Page 17
    17 2.7 Setting up the Stacker 22 2.8 Using the Document smoother 27 2.9 Setting the Paper Thickness 29 2.10 Scanning Documents 30 2.11 Starting Scanning with Button 33 2.12 Feeding Documents Manually 34 2.13 How to use the Scanner Driver 41 2.14 Before Using [Scan] / [Send to] button 64 2.15
  • Fujitsu 5900C | Operator's Guide - Page 18
    Rollers 124 5.6 Replacing the Brake roller 127 6 SOLVING COMMON PROBLEMS .......... 129 6.1 Clearing Document Jams 130 6.2 Error messages of the Operator panel 132 6.3 Troubleshooting 135 6.4 Before Contacting a Service Provider 148 6.5 Labels on the Scanner 150 7 DOCUMENT SPECIFICATIONS
  • Fujitsu 5900C | Operator's Guide - Page 19
    192 8.17 Timeout for Manual Feeding 193 9 OPTIONS 195 9.1 Options 196 9.2 fi-590PRF (Pre-imprinter 197 9.3 fi-590PRB (Post-imprinter 198 9.4 Other Options 199 10 SCANNER SPECIFICATIONS 201 10.1 Basic Product Specifications 202 10.2 Installation Specifications 204 10.3 Dimensions 205 INDEX
  • Fujitsu 5900C | Operator's Guide - Page 20
    xviii
  • Fujitsu 5900C | Operator's Guide - Page 21
    1 NAMES AND FUNCTIONS OF PARTS This chapter describes names and functions of various parts of the scanner. 1.1 Names and Functions of Parts 2 1.2 Operator panel 5 1
  • Fujitsu 5900C | Operator's Guide - Page 22
    the scanner. For scanning long documents. Pull the extension out according to the document's length. Open the cover for cleaning the inner parts of the ADF or for replacing consumables. Button used to open the ADF For the Pre imprinter option The documents loaded onto the Hopper will be fed sheet by
  • Fujitsu 5900C | Operator's Guide - Page 23
    OF PARTS ■ Rear side 1 2 1 3 4 5 6 7 8 No. Name 1 Main power switch 2 Power connector 3 SCSI ID Switch 4 SCSI connector 5 USB connector 6 Extended memory slot 7 VRS slot 8 Extended slot Function For switching the power supply ON/OFF. For connecting the AC cable. Sets the scanner's SCSI
  • Fujitsu 5900C | Operator's Guide - Page 24
    position is set to align the ejected document by the leading edge (see page 24), or when scanning documents with different widths (see page 73). Rollers that pick the paper from the hopper into the ADF. This is a consumable item. Roller used to help separate the paper as the feeding begins. This is
  • Fujitsu 5900C | Operator's Guide - Page 25
    PARTS . Name Function Number display and Function button Function Function Shows the status of the scanner. For details, refer to "Indications on the Function Number Display" (page Using [Scan] / [Send to] button" on page 64, or the FUJITSU TWAIN32 scanner driver help. Power button Use this
  • Fujitsu 5900C | Operator's Guide - Page 26
    and A, c, d, F) are indicated alternately. To return the scanner to the ready status ("1"), press "Scan" or "Send to" button. If this alarm occurs, turn the power off and then on again. If the alarm is indicated after turning on the power again, contact your service engineer. 6 1.2 Operator panel
  • Fujitsu 5900C | Operator's Guide - Page 27
    describes basic scanner operations. This chapter explains operations using the screens of Windows XP. Depending on your OS, your PC's screen shots and the operation may be different from this manual. Be aware that when the FUJITSU TWAIN32 scanner driver, or the FUJITSU ISIS scanner driver is updated
  • Fujitsu 5900C | Operator's Guide - Page 28
    ON 2. Open the Hopper. • Refer to "2.2 Opening and Closing the Hopper" on page 10 to open the HINT Hopper. • Be sure to open the Hopper before turning on the scanner by the Power button. 3. Press the Power button on the Operator panel. The power turns on and the Power button lights up. During
  • Fujitsu 5900C | Operator's Guide - Page 29
    . Thin Send to Scan 2 ⇒The Power button light goes off and the scanner becomes disconnected. If the scanner will not be used for an extended period, turn off the scanner's HINT main power switch on the back and unplug the power cable. BASIC SCANNER OPERATIONS ON OFF 2.1 Turning the
  • Fujitsu 5900C | Operator's Guide - Page 30
    2.2 Opening and Closing the Hopper ■ Opening the Hopper 1. Hold the blue part located on the center of the Hopper. Function Hopper Height Thin Power Thickness Thick Thick Send to Scan Function Hopper Height Thin Power Thickness Thick Send to Scan 10 2.2 Opening and Closing the Hopper
  • Fujitsu 5900C | Operator's Guide - Page 31
    the extension in the Hopper. 2 BASIC SCANNER OPERATIONS Hopper extension 3. Restore the original position of the hopper if the height of Hopper is adjusted. Lower the hopper to the bottom by pressing the button. (Refer to "2.5 Setting the Hopper Height" on page 15) 4. Close the Hopper. Function
  • Fujitsu 5900C | Operator's Guide - Page 32
    2.3 Opening and Closing ADF ■ Opening ADF 1. Remove the document if there is any on the stacker. Function Hopper Height Thin Power Thickness Thick Send to Scan 2. Press the ADF cover open button. Function Hopper Heihgt Thin PowerThickness Thick Send to Scan ⇒The cover is slowly opened.
  • Fujitsu 5900C | Operator's Guide - Page 33
    it is fixed. ATTENTION • When closing the ADF, be sure nothing is left inside of the ADF. • Be careful not to pinch your fingers. BASIC SCANNER OPERATIONS 2.3 Opening and Closing ADF 13
  • Fujitsu 5900C | Operator's Guide - Page 34
    and Closing Top Cover Under the Top cover, there are a storage tray for storing the consumables and cleaning goods and a space for installing the Post-Imprinter. When you use the tray or access the Post-Imprinter, open the top cover as follows. ■ Opening the Top Cover Press the tabs of the
  • Fujitsu 5900C | Operator's Guide - Page 35
    ( ) when the hopper is closed. The hopper may be damaged. 2 Adjustment is not possible when: •The scanner is scanning •The hopper is closed. •When using Software Operation Panel (see page 166). Three hopper heights are available and the corresponding capacities are as follows. High: Up to 100
  • Fujitsu 5900C | Operator's Guide - Page 36
    The adjustment is done by using the Operator Panel on the scanner. Function Function Hopper Height Thin Power Thickness Thick Send to lowered one step lower.(High Middle Low) Immediately after the scanner is turned on, the Hopper is initially set to Low. HINT 16 2.5 Setting the Hopper Height
  • Fujitsu 5900C | Operator's Guide - Page 37
    Scanning HINT Documents with different widths" on page 73. 2 2. Fan the documents. 1) Take a stack of documents about 15mm to 20mm thick (1/2 to 3/4 inch). 2) Hold both ends and bend the documents into an arch. 15 to 20mm BASIC SCANNER OPERATIONS 3) Firmly holding the document with both hands
  • Fujitsu 5900C | Operator's Guide - Page 38
    for document of different size pages, or you want to align the document by the side instead of the center line). (1) Setting the document at the center of the hopper 1. Load the document on the hopper. Place the document face-up on the hopper. 2. Adjust the Side guides to the document width
  • Fujitsu 5900C | Operator's Guide - Page 39
    side of the Side guides. • For long documents, use the hopper extension. height mark 2 BASIC SCANNER OPERATIONS Hopper extension 3. Start the scanner application and scan the document. For the details on how to scan using ScandAll 21, refer to "2.10 Scanning Documents" on page 30. (2)Setting the
  • Fujitsu 5900C | Operator's Guide - Page 40
    2. Lock the side guide not to be used. Flip up the lock switch on the front side of the side guide to lock it. Locked! Lock Switch 3. Move the other side guide to the desired position while pressing down the lock lever. 4. Set the document against the side guide. 20 2.6 Loading Documents on
  • Fujitsu 5900C | Operator's Guide - Page 41
    pages fall under the pick roller. (Otherwise they will not be picked.). 2 Pick roller BASIC SCANNER OPERATIONS 5. Start the scanner application and scan the document. For the details on how to scan using ScandAll 21, refer to "2.10 Scanning Documents" on page 30 If you want to unlock side guides
  • Fujitsu 5900C | Operator's Guide - Page 42
    aligning the leading edge of the ejected documents also. Set up the Stacker by adjusting the Stacker extension, Stopper, Side Guides and Stacker's use the stopper to pull out the stacker extension. It may be damaged. • Be sure to extend the stopper longer than the document. For short documents, use
  • Fujitsu 5900C | Operator's Guide - Page 43
    BASIC SCANNER OPERATIONS When scanning long pages (longer than A3), the document may be longer HINT 2 (The scanner can scan documents up to 863mm long.) 2. Adjust the stacker side guides to the document width. ATTENTION Stacker side guide Be sure to set the stacker side guides a little wider
  • Fujitsu 5900C | Operator's Guide - Page 44
    ■ Switching the stacker's inclination Bottom edge alignment by horizontal stacker setting Leading edge alignment by tilting forward setting of stacker 1. Slide the stacker out towards you. 2. Push down the part of the stacker which is closer to you. ԙ
  • Fujitsu 5900C | Operator's Guide - Page 45
    SCANNER OPERATIONS ⇒The stacker will be fixed in a position tilting forward. • When set to "Bottom edge" position, the stacker does not move up or HINT down and becomes immovable even during scanning operation. • In this position, the stacker's maximum load will be 200 sheets. • If the pages
  • Fujitsu 5900C | Operator's Guide - Page 46
    auto- HINT matically adjust its height according to its load. • When set to the "Bottom edge alignment" position, the stacker's maximum load will be 500 sheets. ATTENTION • On both sides walls of the stacker, photo sensors are installed to detect document height on the stacker. Make sure these
  • Fujitsu 5900C | Operator's Guide - Page 47
    . The Document Smoother will suppress the splattering of ejected pages so they will stack correctly. 1. Prepare the Document Smoother. 2 Tab BASIC SCANNER OPERATIONS 2. Insert one of the tabs into the slit in the scanner. Document Smoother Function Hopper Heihgt Thin Power Thickness Thick
  • Fujitsu 5900C | Operator's Guide - Page 48
    3. While bending the center part, insert the other tab into the scanner slit. ⇒It will look like this when installed. Document Smoother Function Hopper Heihgt Thin Power Thickness Thick Send to Scan 28 2.8 Using the Document smoother
  • Fujitsu 5900C | Operator's Guide - Page 49
    occur, set the thickness level thinner. • Multifeeds, picking failures and paper jams can also occur due to worn-out of the consumables and dirt of the rollers. When such problems are not cleared, change the consumables or clean inside of the scanner. 2.9 Setting the Paper Thickness 29
  • Fujitsu 5900C | Operator's Guide - Page 50
    for Microsoft Windows] - [ScandAll 21]. This starts up ScandAll 21. 4. Select the scanner to use. Select [Select Source] from the [Scan] menu. The [Select source] dialog box appears. Select [FUJITSU Fi-5900Cd] (for TWAIN32 V8, [FUJITSU TWAIN32]). Then click [Select]. 30 2.10 Scanning Documents
  • Fujitsu 5900C | Operator's Guide - Page 51
    resolution, document size and other scan conditions, and 2 click the [Scan] button. For the details on settings in the [TWAIN Driver] dialog box, refer to the "Scanner Utility for Microsoft Windows User's Guide" on the scanner driver CD-ROM. BASIC SCANNER OPERATIONS 2.10 Scanning Documents 31
  • Fujitsu 5900C | Operator's Guide - Page 52
    The image of the scanned document appears on the ScandAll 21 screen. For details on scanning various types of documents, refer to "3 SCANNING VARIOUS TYPES OF DOCUMENTS" on page 69. For details on ScandAll 21 function and operations, refer to ScandAll 21 Help. 32 2.10 Scanning Documents
  • Fujitsu 5900C | Operator's Guide - Page 53
    "2.7 Setting up the Stacker" on page 22. 2 3. Press the [Scan] or [Send to] button. When using the [Scan] button, press the button. When using the [Send to] button, you want to use for scanning and press the [Send to] button. Function Number display Function BASIC SCANNER OPERATIONS Function
  • Fujitsu 5900C | Operator's Guide - Page 54
    the leading edge). •reducing the load on the hopper. •making sure a certain page is scanned. Continuous Feed: Multiple sheets of document are manually fed one at a time and continuously scanned. This is suitable for •manual feed, even if multiple sheets are mistakenly fed, the scanner will scan
  • Fujitsu 5900C | Operator's Guide - Page 55
    side using your finger. Pick Roller Unit 2 Hopper Guide Plate BASIC SCANNER OPERATIONS ⇒The Pick roller unit will click into place. ⇒The hopper will move up to the manual feed At this moment, do not stick the top edge of the document against the inner side of the hopper, instead set them a bit
  • Fujitsu 5900C | Operator's Guide - Page 56
    "2.10 Scanning Documents" on page 30. 4. Start scanning. When using the TWAIN driver, click the [Scan] button on the following screen. 5. Load the documents towards the back of the hopper. When more than one sheet is loaded, only the one on the top of the stack will be fed. The document is picked
  • Fujitsu 5900C | Operator's Guide - Page 57
    to section HINT "8.17 Timeout for Manual Feeding" on page 193. 2 7. To deactivate "Manual Feed Mode" (Single Feed), return the Pick roller unit to its original position. Flip down the small plate on the left using your finger. Pick Roller Unit BASIC SCANNER OPERATIONS 2.12 Feeding Documents
  • Fujitsu 5900C | Operator's Guide - Page 58
    the top edge of the document against the inner side of the hopper, instead set them a bit apart. 4. Start the application and display the scanner driver screen. Set the scanning condition. For the information about how to run the scanner driver, refer to "2.10 Scanning Documents" on page 30. 38
  • Fujitsu 5900C | Operator's Guide - Page 59
    Start scanning. When using the TWAIN driver, click the [Scan] button on the following screen. 2 6. Load the documents towards the back of the hopper. When more than one sheet is loaded, only the one on the top of the stack will be fed. BASIC SCANNER OPERATIONS The document is picked up and ejected
  • Fujitsu 5900C | Operator's Guide - Page 60
    . For setting the timeout for feeding the document manually, refer to section HINT "8.17 Timeout for Manual Feeding" on page 193. 8. To deactivate the "Manual Feed Mode" (Continuous Feed), press down the Hopper Height Button ( ) on the Operator Panel for more than 3 seconds. 40 2.12 Feeding
  • Fujitsu 5900C | Operator's Guide - Page 61
    "FUJITSU ISIS Scanner Driver" in compliance with the ISIS regulation, come with fi-5900C. This section explains how to use each driver using the attached application. ■ FUJITSU TWAIN32 Scanner Driver FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image scanner fi
  • Fujitsu 5900C | Operator's Guide - Page 62
    5. Open the TWAIN Driver window. Select [Scan To View] from the [Scan] menu. ScandAll 21 provides scanning methods as follows: HINT • [To View...]:Displays scanned images on the window. • [To File...:]:Saves for scanning and click the [Scan] button. 42 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 63
    BASIC SCANNER OPERATIONS For details about the settings on this window, refer to "Setting Window for FUJITSU TWAIN32 Scanner Driver" on page 44. ⇒The images of scanned documents are displayed on the [ScandAll 21] window. 2 Depending on the settings of the application software, images may not be
  • Fujitsu 5900C | Operator's Guide - Page 64
    ● Setting Window for FUJITSU TWAIN32 Scanner Driver You can perform settings for the FUJITSU TWAIN32 Scanner Driver on this window. The following describes the main setting items. •For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help" (appears by pressing [Help] or [F1]
  • Fujitsu 5900C | Operator's Guide - Page 65
    ] button Used to undo changes of settings. [Help] button Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also opens by pushing the [F1] key. [About...] button Opens an information window about the FUJITSU TWAIN32 Scanner Driver's version. 2.13 How to use the Scanner Driver 45
  • Fujitsu 5900C | Operator's Guide - Page 66
    the Scanner Operation Panel. [Generic] tab Select this tab to change the unit displayed on the Setting Window for the FUJITSU TWAIN32 Scanner Driver. (Millimeters, Inches, and Pixels are available) [Filter] tab Select this tab for setting the image processing filter(s). Page Edge Filler: Fills
  • Fujitsu 5900C | Operator's Guide - Page 67
    OPERATIONS [Config...] button Click this button for configuring the Setting Files. You can save the changed settings as a Setting File. From next scanning, the settings are quickly changed by using these Setting Files. For details of each function, refer to the "FUJITSU TWAIN32 Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 68
    its Guide or Help for further information. ● Procedure for Basic Scanning Operation 1. Start up the application. From the [Start] menu, select [All Programs]-[QuickScan] and click [QuickScan]. 2. From the menu bar, select [Scan] - [Select Scanner]. ⇒The following window appears. 3. Select fi-5900C
  • Fujitsu 5900C | Operator's Guide - Page 69
    BASIC SCANNER OPERATIONS 5. On the following window, select the profile for scanning. 2 •When creating a new procedure 9. 6. Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor] window. ⇒The configuration window of ISIS driver appears. 2.13 How to use the Scanner Driver 49
  • Fujitsu 5900C | Operator's Guide - Page 70
    of FUJITSU ISIS Scanner Driver" on page 51. 8. On the [Profile Editor] window, click the [OK] button to return to [New batch...] dialog. 9. Load the documents on the hopper. 10. Click the [Scan] button to start scanning. ⇒Scanned images are displayed on the window. Refer to the "QuickScan Overview
  • Fujitsu 5900C | Operator's Guide - Page 71
    ● Configuration Window of FUJITSU ISIS Scanner Driver [Main] tab 2 BASIC SCANNER OPERATIONS Camera Selects the document's side (front or back) to be scanned. The check-marked side(s) #1, you can select either color or gray scale mode for the same side #2. 2.13 How to use the Scanner Driver 51
  • Fujitsu 5900C | Operator's Guide - Page 72
    Guide". To display the "Image Processing Software Option User's Guide", select [Start] > [All Programs] > [Image Processing Software Option] > [User's Guide both text and photographs. Error Diffusion This function minimizes the differences of color levels. 52 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 73
    rear end of the document to scan the whole length of the document. When shorter pages are included in the document, the output images of them are adjusted to the original [sharp]). Increasing this value makes the contrast sharper. 2 BASIC SCANNER OPERATIONS 2.13 How to use the Scanner Driver 53
  • Fujitsu 5900C | Operator's Guide - Page 74
    the page orientation (Portrait or Landscape). Paper Size Selects a paper size according to the size of the document to be scanned. Select any size from the list. [Scan Area...] button Opens the [Scan Area] dialog box. You can specify the area to be scanned. 54 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 75
    Processing] tab 2 BASIC SCANNER OPERATIONS Quick Set: You can Brochures, This option is suitable for scanning documents which have texts etc. and photos (e.g. magazines, brochures). Reverse Image Format Converts colors from/to negative to/from positive. 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 76
    the degree of emphasis from low, mid, and high. Smooth Smooths jaggy images. White Level Follow Use this option when the basic color of documents is not white; for example, when scanning newspaper. Auto value for the white bal- ance.(Photograph mode) 56 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 77
    the background color (Black/White). Multi-feed Detection Multi-feed is an error that occurs when two or more sheets are fed simultaneously. You can set conditions so that the scanner will stop its operation and display an error message when Multifeed is detected. Multi-feed can be detected based on
  • Fujitsu 5900C | Operator's Guide - Page 78
    ". "Custom" is selectable when "Color" is selected on the Main tab. Side: Specifies side(s) to which you want to apply the settings made on this window. Custom Properties Can be specified when "Cutom" is selected in the "Pattern" list. You can specify the numeric values of items such as "Gamma
  • Fujitsu 5900C | Operator's Guide - Page 79
    outlines, only the black part of the letters are scanned. You can use this function when black and white or gray scale is selected. 2 BASIC SCANNER OPERATIONS Enable Color Dropout Color drop out can be specified when "Use Custom Color Dropout" is selected. 2.13 How to use the Scanner Driver 59
  • Fujitsu 5900C | Operator's Guide - Page 80
    dropout of colors with low saturation such as black, which is often used for letters. Sensitivity You can specify the degree of color dropout. The color" window is closed. [Cancel] button Changes are voided and the "Select Dropout color" window is closed. 60 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 81
    BASIC SCANNER OPERATIONS [Compression] tab You can configure compression settings for scanning images in :4:4. [About] tab You can check the version number of the ISIS driver as well as hardware information of the scanner connected to the personal computer. 2.13 How to use the Scanner Driver 61
  • Fujitsu 5900C | Operator's Guide - Page 82
    not print Print before scanning Print after scanning Imprinter is not used. With Pre-Imprinter, printing is done on the front face of the document. With Post-Imprinter, printing is done on the rear face of . You can select delimiters (grouping separators). 62 2.13 How to use the Scanner Driver
  • Fujitsu 5900C | Operator's Guide - Page 83
    .7cm) Minimum unit: 0.1 in.(0.01cm) Units: Selects a unit for Top Margin values i(nch, cm, or pixel). Font: Selects the font to use for printing (Normal, Bold, or Narrow). Rotation: Specifies the orientation of strings of characters. BASIC SCANNER OPERATIONS 2.13 How to use the Scanner Driver 63
  • Fujitsu 5900C | Operator's Guide - Page 84
    , HINT select [Printer and other hardware] and then click [Scanner and camera]. 3. Display the "fi-5900C" properties. For Windows ME and Windows XP, right-click the "fi-5900Cd" icon. For Windows 98 and Windows 2000, double-click the "fi-5900Cd" icon. 4. Select the [Event] tab. 5. Select the event
  • Fujitsu 5900C | Operator's Guide - Page 85
    BASIC SCANNER OPERATIONS Scan button (When clicking on [Scan] button) Send to 1~9(When clicking the [Send to] button) 6. Select the application executed by the event. For Windows XP, select [Performing selected program] under [Performing] and then select the application to be processed. 7. Click OK
  • Fujitsu 5900C | Operator's Guide - Page 86
    on screen. /ScanToFile: Saves scanned image to file. /Exit: Exits the application after scanning. /PROGRES:0 Hides the FUJITSU TWAIN32 progressive indicator window. /SHOWUI:X Displays or hides the FUJITSU TWAIN32 setting window. X=0: To hide, X=1: To display, X=2: To follow the setting
  • Fujitsu 5900C | Operator's Guide - Page 87
    from Scan-Option File setting dialog. FTP server setting dialog Print setting dialog Microsoft SharePoint Portal Server setting dialog Mail setting dialog 4. Click [OK]. 2 BASIC SCANNER OPERATIONS 2.14 Before Using [Scan] / [Send to] button 67
  • Fujitsu 5900C | Operator's Guide - Page 88
    off. •Execute any command from the scanner driver screen in the PC. The waiting time for entering the power saving mode can be set in a range HINT from 5 to 60 minutes in steps of 5 minutes. To set the power saving mode, refer to "8.2 Power saving setting" on page 172. 68 2.15 Resuming from
  • Fujitsu 5900C | Operator's Guide - Page 89
    types of documents. This chapter explains operations using the screens of Windows XP. Depending on your OS, your PC's screen shots and the operation may be different from this manual. Be aware that when the FUJITSU TWAIN32 scanner driver or the FUJITSU ISIS scanner driver is updated, the screens and
  • Fujitsu 5900C | Operator's Guide - Page 90
    stacker in accordance with document size. Refer to section "2.7 Setting up the Stacker" on page 22. 3. Start TWAIN driver with the application used. Refer to section "2.13 How to use the Scanner Driver" on page 41. 4. Set the [Scan Type:] to "ADF (Duplex)". 5. Set resolution and document size and
  • Fujitsu 5900C | Operator's Guide - Page 91
    as depicted below. Thick Paper Stopper Stacker Extension SCANNING VARIOUS TYPES OF DOC- (The scanner can scan documents up to 863mm long.) 3. Start TWAIN driver with the application used. Refer to section "2.13 How to use the Scanner Driver" on page 41. 3.2 Scanning Documents Longer than A3 71
  • Fujitsu 5900C | Operator's Guide - Page 92
    4. Set [Scan Type:] to "Long Page (Front Side)" or "Long Page (Duplex)". Choose "Long Page (Front Side)" when scanning one side; "Long Page (Duplex)", both sides. ⇒The "Set the document size" screen will appear. 5. Click [OK] after setting the document 6. Set resolution and document size and so on,
  • Fujitsu 5900C | Operator's Guide - Page 93
    alongside their center line. For the procedure to align the document with its left (or right) edge, refer to " (2)Setting the document by either Side Guide of the hopper." on page 19. 2. Load the documents on the center of the hopper. Pick roller 3.3 Scanning Documents with different widths 73
  • Fujitsu 5900C | Operator's Guide - Page 94
    by the pick roller. (If the documents are not placed below the Pick roller, the document feeding will not be possible.) Pick roller 3. Align the side guides to the width of the widest document. 原稿 幅 異 場合 4. Align the stacker's position. Refer to "2.7 Setting up the Stacker" on page 22 for
  • Fujitsu 5900C | Operator's Guide - Page 95
    5. Start up the scanner driver. Refer to "2.13 How to use the Scanner Driver" on page 41 for further information about how to start up the scanner driver. 6. Perform the settings for the scanning on the scanner driver's configuration window. For the TWAIN driver Paper size: (Main display) Set the
  • Fujitsu 5900C | Operator's Guide - Page 96
    of Page Detection" is selected - Long Page Scanning • When scanning a paper document and converting the image to PDF using Acrobat, unexpected images may be output when: 1. Setting "Edge Shadow Removal" in Acrobat, and setting "Digital Endorser" or "Black Background" options in the TWAIN driver at
  • Fujitsu 5900C | Operator's Guide - Page 97
    ■ Using ScandAll 21 1. Load the documents on the hopper. 2. Start up ScandAll 21. Select [Program]-[Scanner Utility for Microsoft Windows]-[ScandAll21] from the [Start] menu. 3. From the [Scan] menu select [To Adobe PDF...]. 3 ⇒The [TWAIN Driver] dialog box appears. 4. Set the scan resolution
  • Fujitsu 5900C | Operator's Guide - Page 98
    6. Enter the file name and select the destination to save the scanned image. For details, refer to the descriptions in the [Help] menu of ScandAll 21. 78 3.4 Saving Scanned Images in PDF Format
  • Fujitsu 5900C | Operator's Guide - Page 99
    OF DOC- 4. Select "FUJITSU Fi-5900Cd" at [Scanner] and click [Scan] button. ⇒The [TWAIN driver] dialog box is displayed. ATTENTION Scanning with default settings may yield unexpected results. If that is the case, change the settings as follows: • Uncheck "Recognize Text Using OCR" • Click
  • Fujitsu 5900C | Operator's Guide - Page 100
    ⇒The scanning will be performed. 6. When scanning is finished, click the [Done] button. ⇒The scanned image is displayed. 80 3.4 Saving Scanned Images in PDF Format
  • Fujitsu 5900C | Operator's Guide - Page 101
    SCANNING VARIOUS TYPES OF DOC- 7. Select [Save as...] or [Save] from [File] menu to save the scanned image. 3 For the details on Adobe Acrobat operations, refer to the Adobe Acrobat manual and Help. 3.4 Saving Scanned Images in PDF Format 81
  • Fujitsu 5900C | Operator's Guide - Page 102
    procedure for changing the settings in this dialog box. 1. Start TWAIN Driver from your scanning application. Refer to "2.13 How to use the Scanner Driver" on page 41. 2. Click [Advance...] button in the [TWAIN Driver] dialog box. ⇒The [Advance] dialog box appears. 82 3.5 Excluding a Color from
  • Fujitsu 5900C | Operator's Guide - Page 103
    to be dropped out from [Dropout Color] under [More]. For example, if the document contains black text in green frame, select [Green] so that the scanner only reads the text and eliminates the frames. If you do not wish to have any colors dropped out, select "None". 3 If you wish to
  • Fujitsu 5900C | Operator's Guide - Page 104
    in this screen will be applied and the window is closed. [Cancel] button The settings made in this screen will be aborted and the window is closed. 4. Click [OK] button. [TWAIN Driver] dialog box will be redisplayed. Then, scan the documents using this dialog box. 84 3.5 Excluding a Color from the
  • Fujitsu 5900C | Operator's Guide - Page 105
    will be skipped during scanning. Change settings in the [TWAIN Driver] dialog box to enable skipping blank pages at scanning documents. 1. Start TWAIN Driver from your scanning application. Refer to "2.13 How to use the Scanner Driver" on page 41. 2. Click the [Option...] button in the [TWAIN
  • Fujitsu 5900C | Operator's Guide - Page 106
    When the check box is marked, "Cache Mode" will change to "Ram cache" or "Use both memory". 5. Using the slider control under [Blank Page Skip], specify the Blank Page Skip degree. For white pages, use the [Black Dots Ratio] slider bar to set the skip condition. For black
  • Fujitsu 5900C | Operator's Guide - Page 107
    The [TWAIN Driver] dialog box will be redisplayed. Then, perform the scanning operation on the dialog box. Use the slider bar to set the skip condition in five stages from 1 to 5. The bigger the value, the 3 more likely a page will be detected as blank. 6. Click [OK]
  • Fujitsu 5900C | Operator's Guide - Page 108
    two or more sheets are accidentally fed into the ADF at the same time. You can set the scanner to display an error message or ring the buzzer when the scanner detects a multifeed. Multifeed Detection can be set either through the scanner driver dialog box or through "Software Operation Panel". Refer
  • Fujitsu 5900C | Operator's Guide - Page 109
    "7.5 Multifeed Detection Conditions" on page 158 for detailed information about the document for multifeed detection. 5. Click the [OK] button. The display returns to the [TWAIN Driver] dialog box. Then, perform the scanning operation on the dialog box. ⇒The scanner will stop scanning if multifeed
  • Fujitsu 5900C | Operator's Guide - Page 110
    that are fed into the ADF. The configuration is done through the scanner driver. The following shows the procedure for changing the setting from the [TWAIN Driver] dialog box. 1. Start TWAIN Driver from your scanning application. Refer to "2.13 How to use the Scanner Driver" on page 41. 2. Click
  • Fujitsu 5900C | Operator's Guide - Page 111
    Size and Skew Detection] menu. 3 5. Click the [OK] button. The display returns to the scanning operation [TWAIN Driver] dialog box. ATTENTION When using either of the following documents, the Automatic page size detection may not function correctly. 1. Paper of weight 52g/m2 or less. 2. Non
  • Fujitsu 5900C | Operator's Guide - Page 112
    can be done on the Scanner Driver. The following operation uses the TWAIN driver. 1. Start TWAIN Driver from your scanning application. Refer to "2.13 How to use the Scanner Driver" on page 41. 2. Please check the [Enable Multi Image] checkbox in the [TWAIN Driver] window. Main screen ⇒ The [Multi
  • Fujitsu 5900C | Operator's Guide - Page 113
    SCANNING VARIOUS TYPES OF DOC- 3 3. Select [Multi image output] under "Output mode". 4. Set the order of the output in "Order (for Multi image output)". Primary: Color/Grayscale Secondary: Binary The output order will be: [Color or Grey scale images] → [Binary monochrome images] Primary: Binary
  • Fujitsu 5900C | Operator's Guide - Page 114
    6. Click the [Scan] button to scan the document. 94 3.9 Multi Image Output
  • Fujitsu 5900C | Operator's Guide - Page 115
    be done on the Scanner Driver. The following operation uses the TWAIN driver. 3 1. Start up TWAIN driver fromthe application you are using Refer to "2.13 How to use the Scanner Driver" on page 41. 2. Please check the [Enable Multi Image] checkbox in the [TWAIN Driver] window. SCANNING VARIOUS
  • Fujitsu 5900C | Operator's Guide - Page 116
    screen. The scan settings are done in advance, for the case documents are detected as [Color/Grey scale] or [Monochroe (binary black and white)]. 96 3.10 Color/monochrome Auto Detection
  • Fujitsu 5900C | Operator's Guide - Page 117
    SCANNING VARIOUS TYPES OF DOC- 5. Click the [Scan] button to scan the document. 3 3.10 Color/monochrome Auto Detection 97
  • Fujitsu 5900C | Operator's Guide - Page 118
    98 3.10 Color/monochrome Auto Detection
  • Fujitsu 5900C | Operator's Guide - Page 119
    during operation. Be careful not to get burned. 4.1 Cleaning Materials and Areas Requiring Cleaning .........100 4.2 Cleaning the Pad 102 4.3 Cleaning the Rollers (using the cleaning sheet 103 4.4 Cleaning the Rollers (with a lint-free cloth 106 4.5 Cleaning the Transport path and the sensors
  • Fujitsu 5900C | Operator's Guide - Page 120
    of the cleaning material, contact the FUJITSU scanner dealer where you purchased the scanner. *2)Do not clean the rubber rollers with the cleaner F2, since doing so may cause the rollers to deform or getting damaged. *3)Any lint-free cloth can be used. 100 4.1 Cleaning Materials and Areas Requiring
  • Fujitsu 5900C | Operator's Guide - Page 121
    for each area requiring cleaning. cleaning method cleaning sheet cleaning cycle Pad Pick rollers Brake roller Separator rollers Feed roller Pinch roller Transport path Glass Skew-detection sensor Document sensors every 10,000 scanned pages 3 3 3 3 3 3 cloth moistened with cleaner F1 every
  • Fujitsu 5900C | Operator's Guide - Page 122
    4.2 Cleaning the Pad 1. Open the ADF cover. For details, refer to "2.3 Opening and Closing ADF" on page 12. ADF cover Pad 2. Wipe the Pad (the parts of rubber) with a lint-free cloth, moistened with cleaner F1 (or isopropyl alcohol), in the direction indicated by the arrows. Pad 3. Close the ADF.
  • Fujitsu 5900C | Operator's Guide - Page 123
    4.3 Cleaning the Rollers (using the cleaning sheet) Use the cleaning sheet to clean the upper and lower ADF transport path and the rollers. 1. Open the Pre-Imprinter Cover. Pre-Imprinter Cover 4 Scan 2. While pressing the [Scan] button , press the power button to switch on the scanner. ⇒The function
  • Fujitsu 5900C | Operator's Guide - Page 124
    up the Stacker" on page 22. 7. Remove the protective paper from the cleaning sheet. 8. Place the same cleaning sheet with the adhesive side facing up on the hopper table, aligning its left side with the side guide, as shown in the illustration below. 104 4.3 Cleaning the Rollers (using the cleaning
  • Fujitsu 5900C | Operator's Guide - Page 125
    facing down on the hopper table, aligning its right side with the side guide. Scan 15. [Press the [Scan] button 3 times. ⇒The cleaning sheet will be fed and ejected into the stacker. 16. Press the power button to turn off the scanner. 4.3 Cleaning the Rollers (using the cleaning sheet) 105
  • Fujitsu 5900C | Operator's Guide - Page 126
    in an upper level. For details, refer to "2.5 Setting the Hopper Height" on page 15. 2. Open the ADF cover. For details, refer to "2.3 Opening and Closing ADF" on page 12 ADF Cover Roller Cover Pad Cover 3. Open the roller cover. Grab the depression on the left and right side with your fingers and
  • Fujitsu 5900C | Operator's Guide - Page 127
    and the rubber surface of the Separator rollers using the cleaner F1 or isopropyl alcohol. Pick roller 4 DAILY CARE Separator roller Roller cover 5. Close the roller cover after the cleaning is finished. 6. Open the Pad cover. Grab both sides of the cover, press to the inside and pull down
  • Fujitsu 5900C | Operator's Guide - Page 128
    it upwards to remove it, as shown below. Brake roller 8. Clean the rubber surface of the Brake roller using a lint-free cloth, moistened with the cleaner F1 or isopropyl alcohol. Brake roller 9. Install the Brake roller again after cleaning. Brake roller 10. Close the Pad cover. 108 4.4 Cleaning the
  • Fujitsu 5900C | Operator's Guide - Page 129
    such stains are deteriorating the feeding performance. 4 Feed rollers DAILY CARE ATTENTION Do not use the cleaner F2 for any other parts. Use it only for cleaning the Feed rollers. 12. Clean the Pinch rollers (rubber rollers, each set consists of 2 rollers, 9 locations) on the upper side of the
  • Fujitsu 5900C | Operator's Guide - Page 130
    4.5 Cleaning the Transport path and the sensors 1. Open the ADF cover. For details, refer to "2.3 Opening and Closing ADF" on page 12 2. Clean the whole transport path (stainless and glass parts) using a lint-free cloth moistened with the cleaner F1 or isopropyl alcohol. If the transport path is
  • Fujitsu 5900C | Operator's Guide - Page 131
    CARE 3. Clean the Skew-detection sensor on the lower transport path (7 units at 1 location) using a lint-free cloth moistened with the cleaner F1 or isopropyl alcohol. 4 4. Clean the Skew-detection sensor on the upper transport path (7 units at 1 location) using a lint-free cloth moistened with
  • Fujitsu 5900C | Operator's Guide - Page 132
    on the lower transport path (2 units at 3 locations) using a lint-free cloth moistened with the cleaner F1 or isopropyl alcohol. Document sensor 6. Clean the Document sensors on the upper transport path (2 units at 3 locations) using a lint-free cloth moistened with the cleaner F1 or isopropyl
  • Fujitsu 5900C | Operator's Guide - Page 133
    DAILY CARE 7. Clean the Document sensor on the upper transport path (1 unit at 1 location) using a cotton swab moistened with the cleaner F1 or isopropyl alcohol. 4 Document sensor 8. Close the ADF cover. For details, refer to "2.3 Opening and Closing ADF" on page 12. 4.5 Cleaning the Transport
  • Fujitsu 5900C | Operator's Guide - Page 134
    114 4.5 Cleaning the Transport path and the sensors
  • Fujitsu 5900C | Operator's Guide - Page 135
    REPLACEMENT OF CONSUMABLES This chapter describes how to replace consumables. 5.1 Consumables and Replacement Cycle 116 5.2 How to check and reset the Consumables Counter........ 117 5.3 Replacing the Pad 121 5.4 Replacing the Pick Roller 122 5.5 Replacing the Separator Rollers 124 5.6 Replacing
  • Fujitsu 5900C | Operator's Guide - Page 136
    and reset the Consumables Counter" on page 117 Part Name Pad Part No. PA03450-K014 Standard replacement cycle 600,000 sheets or 1 year Pick Rollers Brake Roller PA03450-K011 600,000 sheets or 1 year PA03450-K013 600,000 sheets or 1 year Separator Rollers Print Cartridge PA03450-K012 600
  • Fujitsu 5900C | Operator's Guide - Page 137
    the counters, use [Software Operation Panel] on you PC as shown below. ■ Checking consumables 1. Turn on the scanner and confirm if it is connected correctly to you PC. 2. From the [Start] menu select [All Programs] [Scanner Utility for 5 Microsoft Windows] [Software Operation Panel] . ⇒The
  • Fujitsu 5900C | Operator's Guide - Page 138
    sheets, scanned since last exchange of the Pick rollers. The number of sheets, scanned since last exchange of the Separator rollers. The remaining ink of the imprinter (sold separately) ink cartridge. (Only displayed when the imprinter option is used) 118 5.2 How to check and reset the Consumables
  • Fujitsu 5900C | Operator's Guide - Page 139
    Click the [Clear] button beside the replaced consumable. 5 2. Click the [OK] button on the displayed confirmation message. ⇒The value of the counter will be reset to "0". ("100", in case of "Remaining Ink"). 3. To close the window of the [Software Operation Panel], click the [OK] button. 5.2 How to
  • Fujitsu 5900C | Operator's Guide - Page 140
    the replacement of consumables, refer to the following sections. Pad: Pick rollers: Separator rollers: Brake roller: "5.3 Replacing the Pad" on page 121 "5.4 Replacing the Pick Roller" on page 122 "5.5 Replacing the Separator Rollers" on page 124 "5.6 Replacing the Brake roller" on page 127 120
  • Fujitsu 5900C | Operator's Guide - Page 141
    to remove it from the scanner. 3. Install the new Pad in the reversed order of the removable. 4. Close the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. 5. Reset the Pad counter. Refer to "5.2 How to check and reset the Consumables Counter" on page 117. 5.3 Replacing the Pad 121
  • Fujitsu 5900C | Operator's Guide - Page 142
    the Pick Roller 1. Open the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. Roller cover 2. Open the roller cover. Put your fingers in the depression on the left and right side and pull the cover towards you to open it. Depression Roller cover 122 5.4 Replacing the Pick Roller
  • Fujitsu 5900C | Operator's Guide - Page 143
    roller correctly on the shaft, until it is locked in place. 5. Close the roller cover. 6. Close the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12 7. Reset the Pick roller counter Refer to "5.2 How to check and reset the Consumables Counter" on page 117 5.4 Replacing the Pick Roller
  • Fujitsu 5900C | Operator's Guide - Page 144
    5.5 Replacing the Separator Rollers 1. Open the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. Roller cover 2. Open the Roller cover. Put your fingers in the depressions on the left and right side and pull the cover towards you to open it. Depression Roller cover 124 5.5 Replacing
  • Fujitsu 5900C | Operator's Guide - Page 145
    as shown below. REPLACEMENT OF CONSUMABLES Separator roller 5 Shaft ⇒The shaft will be locked in outer position and stays there. 4. Remove the rollers from their shafts. Remove both, the left and the right rollers. Separator roller Shaft 5. Put the new rollers (2 rollers, left and right) on
  • Fujitsu 5900C | Operator's Guide - Page 146
    to their original position automatically. Roller cover Separator roller 7. Close the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. 8. Reset the counter of the Separation roller. Refer to "5.2 How to check and reset the Consumables Counter" on page 117. 126 5.5 Replacing the Separator
  • Fujitsu 5900C | Operator's Guide - Page 147
    REPLACEMENT OF CONSUMABLES 5.6 Replacing the Brake roller 1. Move the Hopper down to the "low" position if it is set in an upper level. For details, refer to "2.5 Setting the Hopper Height" on page 15. 2. Open the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. 5 Pad cover 3. Open the
  • Fujitsu 5900C | Operator's Guide - Page 148
    of the shaft into the hole, attach the left end. Brake roller 6. Close the Pad cover. 7. Close the ADF cover. Refer to "2.3 Opening and Closing ADF" on page 12. 8. Reset the Brake roller counter. Refer to "5.2 How to check and reset the Consumables Counter" on page 117. 128 5.6 Replacing the Brake
  • Fujitsu 5900C | Operator's Guide - Page 149
    , how to remedy other problems, items to be checked before contacting an authorized service provider and how to check labels on the scanner. 6.1 Clearing Document Jams 130 6.2 Error messages of the Operator panel 132 6.3 Troubleshooting 135 6.4 Before Contacting a Service Provider 148 6.5 Labels
  • Fujitsu 5900C | Operator's Guide - Page 150
    6.1 Clearing Document Jams When documents have been jammed during scanning, use the following procedure to remove them from the scanner. CAUTION • Take care not to pinch your fingers inside the ADF. • The glass inside the ADF becomes hot during operation. Take care not to burn yourself. • Do not
  • Fujitsu 5900C | Operator's Guide - Page 151
    cause the documents to jam when fed through the scanner. Therefore, remove all staples and clips from the documents before scanning, and examine if the transport path is free from any debris. 4. Close the ADF cover. Refer to ."2.3 Opening and Closing ADF" on page 12. 6.1 Clearing Document Jams 131
  • Fujitsu 5900C | Operator's Guide - Page 152
    Details] button to obtain further solutions for troubleshooting. Error Recovery Guide is stored on the Setup CD-ROM. More details about HINT the installation can be found in the fi-5900C Getting Started under "2.3 Installing the Scanner Application". 132 6.2 Error messages of the Operator panel
  • Fujitsu 5900C | Operator's Guide - Page 153
    /fi-590PRB Imprinter Operator Guide" for further details. U8 One of the following error occurred: 1. Clean the document sensors. 1. Document sensors are dirty. For details, refer to "4.5 Cleaning the Trans- 2. The stacker is full. port path and the sensors" on page 110. 3. The Brake roller
  • Fujitsu 5900C | Operator's Guide - Page 154
    switching mechanism error E10 ROM error E11 Cooling fan error E12 Heater error E15 Extended memory error E16 Option board error E17 The imprinter fuse has blown out. E18 Sensor error E19 LSI error E1A Troubles occurred in the communication inside of the scanner. Solution When
  • Fujitsu 5900C | Operator's Guide - Page 155
    can not resolve the trouble after following the flowcharts, check the items in section "6.4 Before Contacting a Service Provider" on page 148, and then contact an authorized FUJITSU Scanner service provider. Symptom 1 The scanner cannot be turned on. 6 SOLVING COMMON PROBLEMS NO Is the power
  • Fujitsu 5900C | Operator's Guide - Page 156
    YES If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*) Press any button except the Power button. 136 6.3 Troubleshooting
  • Fujitsu 5900C | Operator's Guide - Page 157
    to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. SOLVING COMMON PROBLEMS 6 (*1) Refer to fi-5900C Getting Stated, "2.2 Connecting the scanner to your PC". 6.3 Troubleshooting 137
  • Fujitsu 5900C | Operator's Guide - Page 158
    .(*1) Clean the dirty locations. (*2) YES If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*1) When scanning pictures or
  • Fujitsu 5900C | Operator's Guide - Page 159
    with halftone, grey scale or color, the images might not become sharp and clear. If possible, set the image type on the scanner driver to "Binary black and white". (*2) Refer to "4.5 Cleaning the Transport path and the sensors" on page 110. SOLVING COMMON PROBLEMS 6 6.3 Troubleshooting 139
  • Fujitsu 5900C | Operator's Guide - Page 160
    scanner on a flat, sturdy surface. YES If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*) Refer to "4 DAILY CARE" on page
  • Fujitsu 5900C | Operator's Guide - Page 161
    If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*) Refer to "4.5 Cleaning the Transport path and the sensors" on page 110
  • Fujitsu 5900C | Operator's Guide - Page 162
    and the Brake roller NO clean? Use documents that sheets, until the thickness becomes 50mm or less. Reduce the number of sheets until the weight of the batch of documents becomes less than 5kg. Clean the Pad and the Brake roller (*4) YES Continued on the next page 142 6.3 Troubleshooting
  • Fujitsu 5900C | Operator's Guide - Page 163
    (*6) YES If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*1) Refer to "7.2 Document Quality" on page 153. (*2) Refer to
  • Fujitsu 5900C | Operator's Guide - Page 164
    the Hopper? Use documents that satisfy the requirements. (*1) Fan the documents before loading. (*2) YES NO Are the consumables (Pad/Pick roller/ Separation roller/Brake roller㧕 attached correctly? YES NO Is the Pick roller or Separation roller clean? Attach the consumables correctly (*3) Clean
  • Fujitsu 5900C | Operator's Guide - Page 165
    given in section 6.4, contact an authorized FUJITSU scanner service provider or your dealer. (*1) Refer to "7.2 Document Quality" on page 153. (*2) Refer to "2.6 Loading Documents on the Hopper" on page 17 (*3) Refer to "5 REPLACEMENT OF CONSUMABLES" on page 115. (*4) Refer to "4 DAILY CARE" on
  • Fujitsu 5900C | Operator's Guide - Page 166
    the requirements. (*2) Use the Software Operation Panel to adjust the scan scale. (*3) If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service provider or
  • Fujitsu 5900C | Operator's Guide - Page 167
    edge can be filled white. Use the Software Operation Panel to set the page edge filling area. (*1) If the problem canot be resolved with this flowchart, refer to "6.4 Before contacting a service partner." After checking the items given in section 6.4, contact an authorized FUJITSU scanner service
  • Fujitsu 5900C | Operator's Guide - Page 168
    items before contacting an authorized FUJITSU Scanner service provider or the dealer where you bought the scanner. ■ General descriptions Items to check Model Serial Number Manufacturing date Date of purchase Symptom Frequency of trouble Information example: fi-5900C Check the labels on the
  • Fujitsu 5900C | Operator's Guide - Page 169
    COMMON PROBLEMS Document feeding trouble Items to check Document type Main purpose of use Last cleaning date Last consumable replacement date Operator panel status at trouble Findings Imaging quality trouble Items to check Type and version of scanner driver Interface controller OS (Windows) type
  • Fujitsu 5900C | Operator's Guide - Page 170
    describes how to check the labels on the scanner. The following shows where the two labels are located on the scanner. Label B Label A Label A (example): Indicates scanner information. Barcode Area Label B (example): Indicates various standards that the scanner conforms with. 150 6.5 Labels on the
  • Fujitsu 5900C | Operator's Guide - Page 171
    7 DOCUMENT SPECIFICATIONS This chapter describes the sizes and qualities of documents required for the satisfactory performance of the scanner. 7.1 Document Size 152 7.2 Document Quality 153 7.3 Maximum Document Loading Capacity 156 7.4 Hole-punching Prohibited Areas 157 7.5 Multifeed Detection
  • Fujitsu 5900C | Operator's Guide - Page 172
    7.1 Document Size The following shows the supported document sizes. A Feeding Direction B A 304.8 mm (12 in) Maximum B 431.8 mm * (17 in) A 53 mm (2.087 in) Minimum B 74 mm (2.913) *When scanning in "long page", the maximum scannable length is 863 mm (34 in). 152 7.1 Document Size
  • Fujitsu 5900C | Operator's Guide - Page 173
    and thickness of documents this scanner supports. ■ Document type The recommended document types are as follows. •Wood free paper 7 •Wood containing paper When using documents of a paper type other than the above, perform a test-scanning with a few sheets of the same type before executing
  • Fujitsu 5900C | Operator's Guide - Page 174
    that are not square or rectangular •Very thin documents Do not use the following documents: •Paper-clipped or stapled documents •Documents on the rollers more frequently. • When feeding errors, paper jams and multifeeds occur frequently, refer to "2.9 Setting the Paper Thickness" on page 29
  • Fujitsu 5900C | Operator's Guide - Page 175
    Pad or rollers (e.g. Pick roller) when documents are fed. Pay attention to the following: Cleaning: If pick errors occur frequently, clean the Pad and the Pick roller. For details on cleaning the Pad and the Pick roller, refer to "4 DAILY CARE" on page 99 Replacing parts: The service life of
  • Fujitsu 5900C | Operator's Guide - Page 176
    paper weight. Hopper height : Low 500 Hopper height : Middle Hopper height : High Hopper's Loading Capacity (Sheets) 300 250 150 100 50 31 Paper weight conversion table Unit g/m2 31 52 64 lb 10 14 17 80 157 Paper weight㧔g/m) 209.3 Conversion 75 80 90 104 127 157 209.3 20
  • Fujitsu 5900C | Operator's Guide - Page 177
    holes in the shaded areas may cause errors. For job separation sheet requirements, refer to "7.7 Job Separation Sheet" on page 161. 35 Reference Point 㧔Unit : mm㧕 Leading edge 7 Front Side Feeding Direction 15 DOCUMENT SPECIFICATIONS Center line Bottom edge If there are any holes in the
  • Fujitsu 5900C | Operator's Guide - Page 178
    7.5 Multifeed Detection Conditions The following describes the conditions required for Multifeed detection: ■ Check overlapping •Paper weight: 31 - 209.3 g/m2 (8.3 to 56.1 lb) •Punched holes are not allowed within 35 mm (1.4 in) of the vertical lines of the center, right and left sides of the the
  • Fujitsu 5900C | Operator's Guide - Page 179
    Feeding Direction Feeding Direction DOCUMENT SPECIFICATIONS 35 35 35 35 㧔Unit: mm㧕 7 60 60 Fig.1 Fig.2 When you want to detect overlapping, be sure that paper documents are not HINT clinging
  • Fujitsu 5900C | Operator's Guide - Page 180
    the shaded area as shown in the Figure below. The top 3mm on both sides of a document, should have no printing in this area. When using dropout color, the color can be in this area. If this cannot be followed, turn the white level follower off when reading. Reading reference position
  • Fujitsu 5900C | Operator's Guide - Page 181
    Shape The following shows the typical format of the job separation sheet. 15 (0.59") 7 Feeding direction 15 (0.59") DOCUMENT SPECIFICATIONS Center of document more than 210 (8.27") (Unit : mm) 2. Document Specifications Document width must be A4 width (210mm/8.27") or wider. 7.7 Job Separation
  • Fujitsu 5900C | Operator's Guide - Page 182
    When scanning documents of different thickness/Friction Coefficients/sizes using this scanner, the following restrictions apply. Before you scan any mixed documents, always test scan a few pages to see if the mixed document can be properly fed. (For details on how to scanning mixed documents, refer
  • Fujitsu 5900C | Operator's Guide - Page 183
    DOCUMENT SPECIFICATIONS Maximum Size A3 DL B4 LTR A4 B5 A5 B6 A6 B7 A7 B8 be moved when the larger document is being picked up, adversely affecting feeding performance. When setting the document, try to meet the following condition: Pick Roller Document
  • Fujitsu 5900C | Operator's Guide - Page 184
    164 7.8 Scanning Mixed Documents
  • Fujitsu 5900C | Operator's Guide - Page 185
    can be done for the scanner using the Software Operation Panel. 8.1 Scanner Settings 166 8.2 Power saving setting 172 8.3 Offset/Scan scale 173 8.4 Multifeed Detection 175 8.5 Page Edge Filler (ADF 179 8.6 Dropout Color 181 8.7 Pre-Pick 182 8.8 Page Edge Filler (Automatic paper size detection
  • Fujitsu 5900C | Operator's Guide - Page 186
    installed together with the scanner driver (TWAIN/ISIS). With this application, you can configure settings and functions for the fi-5900C. ■ Start up the Software Operation Panel Start up via PC 1. Confirm if the scanner is connected correctly to the PC, then power on the scanner. 2. From the [Start
  • Fujitsu 5900C | Operator's Guide - Page 187
    show . 8 When pressing the [Function] button, the Function Number Display will change in the following way: [1] [2] ... [9] [C]. Send to 3. Press the [Send to] button. ⇒The [Software Operation Panel] window will be displayed. SCANNER SETTINGS 8.1 Scanner Settings 167
  • Fujitsu 5900C | Operator's Guide - Page 188
    For evaluating the consumable Pad/Pick roller/Separator Roller/Brake - replacement cycle. roller Use this function to reset the counters remaining ink level (only for the after replacing consumables. imprinter option) Refer to "5.1 Consumables and Replacement Cycle" on page 116 Select the
  • Fujitsu 5900C | Operator's Guide - Page 189
    settings (parameters) in the lower part. 8 SCANNER SETTINGS Item Multifeed Page edge filler (ADF) Explanation Selectable parameter detected as Refer to "8.4 Multifeed Detec- length difference): 10, 15 or 20mm tion" on page 175 Deactivated Fill the end sections of a specifiedmm-wide with
  • Fujitsu 5900C | Operator's Guide - Page 190
    Page edge filler (Automatic paper size detection) specification for Multifeed Detection Specify the area to be detected for Left/Middle/Right multifeed. You can select left, middle, or right for detection. Refer to "8.4 Multifeed Detection" on page Round Down 16-bit 5 Yes 170 8.1 Scanner Settings
  • Fujitsu 5900C | Operator's Guide - Page 191
    /Forcibly select Post-imprinter Timeout for man- Specify the standby time period. 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, ual feeding After the predetermined time 100, 110 (seconds) period has elapsed, manual feeding mode is canceled. 10 seconds 8 SCANNER SETTINGS 8.1 Scanner Settings 171
  • Fujitsu 5900C | Operator's Guide - Page 192
    the power saving mode. Configure the Power saving mode as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the [Device Setting] tab. 3. Use the slide control bar to set the waiting time before entering the power saving mode. Setting range
  • Fujitsu 5900C | Operator's Guide - Page 193
    is elongated, use the following procedure to adjust the Offset and the Scan scale for correction. ATTENTION The factory default setting are appropriate, so normally there is no need to make any adjustment. 8 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166
  • Fujitsu 5900C | Operator's Guide - Page 194
    3. Adjust the Offset/Scan scale as necessary. Offset setting Target: Horizontal: Vertical: Select ADF front or ADF back as target. Adjusts the horizontal Offset. Setting range -2mm to +3mm, in steps of 0.5mm. Adjusts the vertical Offset. Setting range -2mm to +3mm, in steps of 0.5mm. Scan scale
  • Fujitsu 5900C | Operator's Guide - Page 195
    Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. From the [Device Setting 2] tab select "Multifeed". SCANNER SETTINGS used for monitoring the fed documents. When checking the document length, select the length difference for which a Multifeed will be detected. Select 10/
  • Fujitsu 5900C | Operator's Guide - Page 196
    case, the scanner driver selection will have priority) When [Check overlapping] is selected as the detection method, you can also specify the detection area. 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Document check area specification for
  • Fujitsu 5900C | Operator's Guide - Page 197
    middle, or right. Left Middle Right 35 35 35 8 Feeding direction SCANNER SETTINGS Document 60 60 Unit: mm Selected mode: You can specify the can specify the starting position of the selected range by the length from the edge of the paper document. Range: 0 to 510mm, in increments of 2mm,
  • Fujitsu 5900C | Operator's Guide - Page 198
    Setting Example 1: Specified area = Right, Selected mode = Non-detection area, Start = 50mm, End = 200mm 35 35 35 50 200 Feeding direction Unit: mm 60 60 Setting Example 2: Specified area = Middle, Selected mode = Detection area, Start = 50mm, End = 200mm 35 35 35 50 200 Feeding
  • Fujitsu 5900C | Operator's Guide - Page 199
    by using the "Page Edge Filler" function. This function fills the end portion of the image so that it looks clean. Configure the settings for the Page Edge Filler as follows: 1. Start up the Software Operation Panel. 8 Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Page Edge Filler
  • Fujitsu 5900C | Operator's Guide - Page 200
    " using the scanner driver. If you are using the TWAIN driver, do the following to change the back- ground color to black: Select the [Option] button, and then select [Black background] from [Automatic Size and Skew detection] on the [Rotation] tab. ATTENTION Note that if the Page Edge Filler
  • Fujitsu 5900C | Operator's Guide - Page 201
    colors than red, green, and blue. If you want to drop out any other colors, use the scanner driver setting window. For details on how to configure settings through the scanner driver setting window, refer to "3.5 Excluding a Color from the image (drop out color)" on page 82 8.6 Dropout Color 181
  • Fujitsu 5900C | Operator's Guide - Page 202
    between the scanning of two separate documents can be shortened. Configure the settings for the Pre-Pick as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Pre-Pick" setting on the [Device Setting 2] tab. 3. Select "Yes" or "No" for Pre
  • Fujitsu 5900C | Operator's Guide - Page 203
    so that it looks clean. Configure the settings for "Page Edge Filler (Automatic paper size detection)" as follows: 8 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Page Edge Filler (Automatic paper size detection)" setting on the [Device
  • Fujitsu 5900C | Operator's Guide - Page 204
    "Automatic Paper Size Detection" setting can be configured on the HINT scanner driver setting window. For details on how to set the setting, refer to "3.8 Correcting skewed Docu- ments" on page 90 ATTENTION Note that if the Page Edge Filler is too wide, some characters in the vicinity of the
  • Fujitsu 5900C | Operator's Guide - Page 205
    and scanned smoothly, use this mode. In this mode, sheets of paper are fed at a slower speed so that thin paper can be fed and scanned properly. Follow the steps below to switch to the Thin Mode. 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the
  • Fujitsu 5900C | Operator's Guide - Page 206
    8.10 Paper Jam Detection You can set the degree of detection sensitivity for a jam at the feeder. Configure the settings for Paper Jam Detection as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Paper jam detection" setting on the [
  • Fujitsu 5900C | Operator's Guide - Page 207
    the settings for the AutoCrop Boundary as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "AutoCrop Boundary" setting on the [Device Setting 2] tab. 8 SCANNER SETTINGS 3. Select "Round Up" if you want to prevent the output image
  • Fujitsu 5900C | Operator's Guide - Page 208
    follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "SCSI Bus Width" setting on the [Device Setting 2] tab. 3. Select either 16-bit or 8-bit. ATTENTION To use SCSI cards and/or SCSI cables that do not support Ultra Wide SCSI, select "8-bit
  • Fujitsu 5900C | Operator's Guide - Page 209
    Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Auto Color Detection" setting on the [Device Setting 2] tab. 8 SCANNER on the scanner driver HINT setting window. For details on how to set the setting, refer to "3.10 Color/monochrome Auto Detection" on page 95.
  • Fujitsu 5900C | Operator's Guide - Page 210
    . Configure the settings for the Alarm setting as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. Select the "Alarm setting" on the [Device Setting 2] tab. 3. Select "Alarm at error" to sound beeps when a jam or multifeed occurs. Select "No alarm at
  • Fujitsu 5900C | Operator's Guide - Page 211
    are fed outside of the scannable area due to over-skew, is judged as a jam. You can turn it On and Off. Configure the settings for the Jam detection outside of scannable area when transporting... as follows: 1. Start up the Software Operation Panel. 8 Refer to "8.1 Scanner Settings" on page 166
  • Fujitsu 5900C | Operator's Guide - Page 212
    Complies with the scanner driver setting. Pre-imprinter is forcibly used to print unless directed by the scanner driver. Post-imprinter is forcibly used to print unless directed by the scanner driver. For details on the specifications of the imprinter, refer to "9 OPTIONS" on HINT page 195. 192
  • Fujitsu 5900C | Operator's Guide - Page 213
    for the Timeout for Manual as follows: 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 8 2. Select the "Timeout for Manual Feeding" setting on the [Device Setting 2] tab. SCANNER SETTINGS 3. Select the timeout period for manual feeding. You can specify
  • Fujitsu 5900C | Operator's Guide - Page 214
    194 8.17 Timeout for Manual Feeding
  • Fujitsu 5900C | Operator's Guide - Page 215
    9 OPTIONS This chapter describes options for fi-5900C. 9.1 Options 196 9.2 fi-590PRF (Pre-imprinter 197 9.3 fi-590PRB (Post-imprinter 198 9.4 Other Options 199 195
  • Fujitsu 5900C | Operator's Guide - Page 216
    options available for the scanner. Name fi-590PRF PreImprinter Part No. PA3450-D700 fi-590PRB PostImprinter PA3450-D710 FUJITSU scanner dealer where you purchased the scanner or FUJITSU group company responsible for your country. ATTENTION Both imprinters can be installed on the scanner at
  • Fujitsu 5900C | Operator's Guide - Page 217
    operations in such areas are not guaranteed. Printing Position Accuracy Consumables Vertical: ± 4mm Horizontal: ± 4mm Print Cartridge As for the operations and functions of fi-590PRF (Pre-imprinter), refer to the fi-590PRF Operator's Guide attached to fi-590PRF. 9.2 fi-590PRF (Pre-imprinter
  • Fujitsu 5900C | Operator's Guide - Page 218
    of the scanner. It prints after the scanning. fi-590PRB (Post-imprinter) Specifications are described below operations in such areas are not guaranteed. As for the operations and functions of fi-590PRB (Post-imprinter), refer to the fi-590PRB Operator's Guide attached to fi-486PRRE. 198 9.3 fi
  • Fujitsu 5900C | Operator's Guide - Page 219
    you install extended memory, please first touch metal objects to release static. 9 OPTIONS 1. Switch off the scanner's main power switch, unplug all connecting cables. 2. Unscrew the back cover of the scanner and take it off. Screw Cover 3. Insert the memory into the slot, and push down the
  • Fujitsu 5900C | Operator's Guide - Page 220
    of the same specification must be installed at the same time. The memory modules are not provided with the scanner. Memory type: 144 or not HINT through the [Software Operation Panel]: Click the [Device Setting] tab and check the value of scanner memory under "Standard Information". 200 9.4
  • Fujitsu 5900C | Operator's Guide - Page 221
    10 SCANNER SPECIFICATIONS This chapter describes the Scanner Specifications. 10.1 Basic Product Specifications 202 10.2 Installation Specifications 204 10.3 Dimensions 205 201
  • Fujitsu 5900C | Operator's Guide - Page 222
    10.1 Basic Product Specifications 1 Scanner Type ADF (Automatic Document - Feeder) and Manual feed 2 Image sensor Color CCD x 2 Front/Back 3 Light source Incandescent cold cathode fluorescent lamp x 2 Front/Back 4 Scanning area Minimum 53 mm x 74 mm, 2.1 in. x 2.9 - in. Maximum
  • Fujitsu 5900C | Operator's Guide - Page 223
    to scanning on the front side of the document. The fi-590PRB (post-imprinter) will print after the scanning on the back side of the document. You can install both the fi-590PRF and fi-590PRB, but you cannot use them at the same time. 10 SCANNER SPECIFICATIONS 10.1 Basic Product Specifications 203
  • Fujitsu 5900C | Operator's Guide - Page 224
    (kg) 50 kg (110.4lb) AC100 - 240 V±10% Single-phase 50/60 Hz ±3Hz 250 W or less Operating 15 to 35 degrees Celsius 59 to 95 degrees Fahrenheit 20 - 80% 172 kcal or less 70 Front Not operating -20 to +60 degrees Celsius -4 to +140 degrees Fahrenheit 8 - 95% 204 10.2 Installation Specifications
  • Fujitsu 5900C | Operator's Guide - Page 225
    SCANNER SPECIFICATIONS 10.3 Dimensions 10 unit: mm 10.3 Dimensions 205
  • Fujitsu 5900C | Operator's Guide - Page 226
    206 10.3 Dimensions
  • Fujitsu 5900C | Operator's Guide - Page 227
    30 Basic Scanner Operations 7 Brake roller 4, 127 Brake roller unit 124 C Cleaner F1 100 Cleaner F2 100 Cleaning Pad 102 Cleaning materials 100 Cleaning sheet 100 Configuration Window of FUJITSU ISIS Scanner Driver 51 Consumables 116 Abrasion counters 117 Replacement cycle 116 Correcting
  • Fujitsu 5900C | Operator's Guide - Page 228
    button 5 Separation roller 101 Separator roller 4 Service provider 148 Setting Window for FUJITSU TWAIN32 Scanner Driver 44 Side guide 2 Side guides 18 Skipping blank Pages 85 Specifications 202 ADF capacity 202 Document thickness 202 Grayscale level 202 Image sensor 202 Interface 202
  • Fujitsu 5900C | Operator's Guide - Page 229
    IN-3
  • Fujitsu 5900C | Operator's Guide - Page 230
    fi-5900C Image Scanner Operator's Guide P3PC-1432-02ENZ0 Date published: February, 2006 PFU LIMITED •Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law. •The contents of this manual are subject to change without
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
Operator's Guide
fi-5900C Image Scanner
P3PC-1432-02ENZ0
Send to
Scan
Power Thickness
Hopper Hei
ght
Function
Thick
Thin