Fujitsu 5900C Operator's Guide - Page 195

Multifeed Detection

Get Fujitsu 5900C - fi - Document Scanner PDF manuals and user guides
UPC - 097564306945
View all Fujitsu 5900C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 195 highlights

8.4 Multifeed Detection Multifeed refers to the phenomenon, when two or more documents are fed overlapping at once into the scanner. This may cause the loss of important data. To prevent this, this scanner is equipped with a Multifeed detection function. When function is activated, a message will be displayed and the scanning interrupted in case a Multifeed has been detected. Configure the settings for the Multifeed detection as follows. 8 1. Start up the Software Operation Panel. Refer to "8.1 Scanner Settings" on page 166. 2. From the [Device Setting 2] tab select "Multifeed". SCANNER SETTINGS 3. Select the detection method. Deactivated: Check overlapping: Check length difference: Check overlapping and length difference: Length: No Multifeed detection will be performed. Document overlapping will be monitored. The difference of the documents length will be monitored. [Check overlapping] and [Check length difference], both parameters will be used for monitoring the fed documents. When checking the document length, select the length difference for which a Multifeed will be detected. Select 10/15/20mm. If the detected document length is smaller than the selected size, it will be recognized as a Multifeed. 8.4 Multifeed Detection 175

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
175
8.4 Multifeed Detection
8
SCANNER SETTINGS
8.4
Multifeed Detection
Multifeed refers to the phenomenon, when two or more documents are fed overlapping at once into the
scanner.
This may cause the loss of important data.
To prevent this, this scanner is equipped with a Multifeed detection function.
When function is activated, a message will be displayed and the scanning interrupted in case a Multifeed
has been detected.
Configure the settings for the Multifeed detection as follows.
1.
Start up the Software Operation Panel.
Refer to
“8.1 Scanner Settings” on page 166
.
2.
From the [Device Setting 2] tab select “Multifeed”.
3.
Select the detection method.
Deactivated:
No Multifeed detection will be performed.
Check overlapping:
Document overlapping will be monitored.
Check length difference:
The difference of the documents length will be monitored.
Check overlapping and
length difference:
[Check overlapping] and [Check length difference], both parameters will
be used for monitoring the fed documents.
Length:
When checking the document length, select the length difference for
which a Multifeed will be detected. Select 10/15/20mm. If the detected
document length is smaller than the selected size, it will be recognized as a
Multifeed.