HP 9200C HP 9200c Digital Sender - Support Guide - Page 59

Options, Values, Explanation, DIAGNOSTICS, DEST IP, PACKET SIZE, TIMEOUT, COUNT, PRINT RESULTS,

Get HP 9200C - Digital Sender PDF manuals and user guides
UPC - 829160458878
View all HP 9200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Item DIAGNOSTICS Options LOOPBACK TEST CAUTION This test erases your TCP/IP configuration. Values YES NO PING TEST DEST IP PACKET SIZE TIMEOUT COUNT PRINT RESULTS EXECUTE Explanation Select YES to initiate the loopback test. Loopback verifies that TCP/IP is installed and correctly configured on the local device. If a reply is returned then you know that the TCP/ IP stack is functioning correctly. Fill in each of the settings before performing the ping test. The ping test verifies end-to-end connectivity by sending an Internet Control Message Protocol packet to see if a destination host is responding. DEST IP specifies the IP address of the remote host. PACKET SIZE specifies the size of each packet, in bytes, to be sent to the remote host. The minimum (and default) is 64 and the maximum is 2048. TIMEOUT specifies the length of time, in seconds, to wait for a response from the remote host. The default is 1 and the maximum is 100. COUNT specifies the number of test packets to send for this test. Select a value from 1 to 100. To configure the test to run continuously, select 0. The PRINT RESULTS option does not apply to the digital sender. Select EXECUTE and then select YES to initiate the ping test. ENWW Using the control-panel menus 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Item
Options
Values
Explanation
DIAGNOSTICS
LOOPBACK TEST
CAUTION
This test erases
your TCP/IP
configuration.
YES
NO
Select
YES
to initiate the
loopback test.
Loopback verifies that TCP/IP
is installed and correctly
configured on the local
device. If a reply is returned
then you know that the TCP/
IP stack is functioning
correctly.
PING TEST
DEST IP
PACKET SIZE
TIMEOUT
COUNT
PRINT RESULTS
EXECUTE
Fill in each of the settings
before performing the ping
test. The ping test verifies
end-to-end connectivity by
sending an Internet Control
Message Protocol packet to
see if a destination host is
responding.
DEST IP
specifies the IP
address of the remote host.
PACKET SIZE
specifies the
size of each packet, in bytes,
to be sent to the remote host.
The minimum (and default) is
64 and the maximum is 2048.
TIMEOUT
specifies the
length of time, in seconds, to
wait for a response from the
remote host. The default is 1
and the maximum is 100.
COUNT
specifies the number
of test packets to send for this
test. Select a value from 1 to
100. To configure the test to
run continuously, select 0.
The
PRINT RESULTS
option
does not apply to the digital
sender.
Select
EXECUTE
and then
select
YES
to initiate the ping
test.
ENWW
Using the control-panel menus
51