HP Scitex FB10000 Site Preparation Guide Rev. 2 - Page 32

Floor Surface and Strength, Additional Floor Surface Information

Get HP Scitex FB10000 PDF manuals and user guides View all HP Scitex FB10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Floor Surface and Strength Note The customer is strictly responsible for surface and load-bearing compliance. The following information is provided to assist the engineer: • The floor must be strong enough to support the machine while standing on its 6 supporting pads (see Figure 4-1) and 20 legs. • The machine weight is approximately 8200 kg (18077 lbs.). • A single supporting pad foot print is 111 x 111 mm (4.4 x 4.4 in.) • The floor must be leveled with a maximum incline of 0.2%. Figure 4-1 Leveling and Supporting Pads - Specifications Additional Floor Surface Information When planning the print production area, it is important to ensure that the floor surface is solid, smooth, level, and free from any holes or indentations. The floor should be constructed of smooth concrete. The floor of the print production area, as well as that on machine's way from the unpacking area, must be strong enough to support the entire weight of the printer, including all accompanying equipment (see Figure 4-1). A construction engineer should be consulted regarding the load-bearing capabilities of the floor of the building where the FB10000 press is to be installed. Note Installation of the machine loader requires drilling ten (10) holes into the floor. 24 HP Scitex FB10000 Site Preparation Guide, Rev. 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
24
HP Scitex FB10000 Site Preparation Guide, Rev. 2
Floor Surface and Strength
Note
The customer is strictly responsible for surface and load-bearing compliance.
The following information is provided to assist the engineer:
•
The floor must be strong enough to support the machine while standing on its 6
supporting pads (see
Figure 4-1
) and 20 legs.
•
The machine weight is approximately
8200 kg
(18077 lbs.).
•
A single supporting pad foot print is
111 x 111 mm
(4.4 x 4.4 in.)
•
The floor must be leveled with a maximum incline of
0.2%
.
Figure 4-1
Leveling and Supporting Pads — Specifications
Additional Floor Surface Information
When planning the print production area, it is important to ensure that the floor
surface is solid, smooth, level, and free from any holes or indentations. The floor
should be constructed of smooth concrete.
The floor of the print production area, as well as that on machine's way from the
unpacking area, must be strong enough to support the entire weight of the printer,
including all accompanying equipment (see
Figure 4-1
).
A construction engineer should be consulted regarding the load-bearing capabilities
of the floor of the building where the FB10000 press is to be installed.
Note
Installation of the machine loader requires drilling ten (10) holes into the floor.