HP Vectra VL 5/xxx HP Vectra VL 5/xxX Series 3 PC - User’s Guide - Page 61

If You Can't Start the SETUP Program

Get HP Vectra VL 5/xxx - 3 PDF manuals and user guides View all HP Vectra VL 5/xxx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

# $ K + If You Can't Start the SETUP Program This may be due to the copy of the PC's configuration in memory being corrupted by a program. You will need to erase this bad configuration. To clear the configuration: 1. Switch off the PC and remove the cover. (Refer to chapter 3.) 2. Set the system board switch 3 (CONFG) on the switch block to CLOSED to clear the configuration. (Refer to chapter 5 for the switch location.) 3. Switch on the PC to erase the memory. 4. Check that error messages are displayed, and wait until the PC has started. 5. Switch off the PC. 6. Set the system board switch 3 (CONFG) on the switch block to OPEN to re-enable the configuration. 7. Replace the cover. (Refer to chapter 3.) 8. Switch on the PC and run SETUP by pressing[F2] when appears. 9. Press [F3] to save the configuration and exit from SETUP. # IfYouCan.tStarttheSETUPProgram.57 $ If You Can't Start the SETUP Program K If You Can't Start the SETUP Program + SECTION4:0070 HP Vectra VL5 PC User's Guide - Part 2Error! No text of specified style in document. • 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
HP Vectra VL5 PC User's Guide - Part 2
Error! No text of specified style in document.
•
61
#
$
K
+
If You Can't Start the SETUP Program
This may be due to the copy of the PC's configuration in memory being corrupted by a
program. You will need to erase this bad configuration.
To clear the configuration:
1.
Switch off the PC and remove the cover. (Refer to chapter 3.)
2.
Set the system board switch 3 (CONFG) on the switch block to CLOSED to clear the
configuration. (Refer to chapter 5 for the switch location.)
3.
Switch on the PC to erase the memory.
4.
Check that error messages are displayed, and wait until the PC has started.
5.
Switch off the PC.
6.
Set the system board switch 3 (CONFG) on the switch block to OPEN to re-enable the
configuration.
7.
Replace the cover. (Refer to chapter 3.)
8.
Switch on the PC and run SETUP by pressing
[F2]
when
<Setup=F2>
appears.
9.
Press
[F3]
to save the configuration and exit from SETUP.
#
IfYouCan.tStarttheSETUPProgram.57
$
If You Can't Start the SETUP Program
K
If You Can't Start the SETUP Program
+
SECTION4:0070