Panasonic AW-HE130 Operating Instructions - Page 18

Parts and their functions, Camera unit

Get Panasonic AW-HE130 PDF manuals and user guides View all Panasonic AW-HE130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Parts and their functions Camera unit 4 8 Rear panel 1 2 5 7 4 3 6 16 22 18 21 13 9 11 10 17 15 23 14 12 19 20 21 Bottom panel 3 25 24 1. Mount bracket for installation surface (supplied accessory) Mount this bracket onto the installation surface, and then attach the camera main unit to the bracket. 2. Drop-prevention wire This wire is screwed down to the bottom panel of the camera main unit. Loop the circle part of the wire around the hook of the mount bracket. 3. Hole for securing the camera pedestal This hole is provided in the bottom panel of the camera pedestal. 4. Wireless remote control signal light-sensing area The light-sensing area is provided in three places, on the front panel of the camera pedestal and at the top of the rear panel. 5. Status display lamp This lights in the following way depending on the status of the unit. Orange: When the standby status is established Green: When the power is on Red: When trouble has occurred in the unit Green and blinks twice: When a signal matched by the remote control ID has been received from the wireless remote control (optional accessory) while the power is on Orange and blinks twice: When a signal not matched by the remote control ID has been received from the wireless remote control (optional accessory) while the power is on 6. Camera head This rotates in the up and down direction. 7. Tilt head This rotates in the right and left direction. 8. Tally lamp This comes on or goes off in response to the control from the controller but only when "On" has been selected as the tally lamp use setting. 9. RS-422 connector [RS-422] This RS-422 connector (RJ45) is connected when exercising serial control over the unit from an external device. Use a cable with the following specifications for the connection to this connector. The tally lamp can be lit by shorting the TALLY signal (pin 2) with GND (pin 1). • Do not apply a voltage to the TALLY signal pin. LAN cable*(category 5 or above, straight cable), max. 1000 m [3280 ft] *: Use of an STP (shielded twisted pair) cable is recommended. Pin No. Signal 1 GND 2 TALLY 3 RXD- 4 TXD- Pin No. Signal 5 TXD+ 6 RXD+ 7- 8- 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
1
2
5
7
4
3
6
4
8
3
25
24
16
22
18
9
10
13
21
15
23
14
17
11
12
20
19
21
Rear panel
Bottom panel
1.
Mount bracket for installation surface
(supplied
accessory)
Mount this bracket onto the installation surface, and then attach the
camera main unit to the bracket.
2.
Drop-prevention wire
This wire is screwed down to the bottom panel of the camera main
unit. Loop the circle part of the wire around the hook of the mount
bracket.
3.
Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera pedestal.
4.
Wireless remote control signal light-sensing area
The light-sensing area is provided in three places, on the front panel
of the camera pedestal and at the top of the rear panel.
5.
Status display lamp
This lights in the following way depending on the status of the unit.
Orange:
When the standby status is established
Green:
When the power is on
Red:
When trouble has occurred in the unit
Green and blinks twice:
When a signal matched by the remote control ID has
been received from the wireless remote control (optional
accessory) while the power is on
Orange and blinks twice:
When a signal not matched by the remote control ID has
been received from the wireless remote control (optional
accessory) while the power is on
6.
Camera head
This rotates in the up and down direction.
7.
Tilt head
This rotates in the right and left direction.
8.
Tally lamp
This comes on or goes off in response to the control from the
controller but only when “On” has been selected as the tally lamp use
setting.
9.
RS-422 connector [RS-422]
This RS-422 connector (RJ45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
The tally lamp can be lit by shorting the TALLY signal (pin 2) with
GND (pin 1).
<NOTE>
• Do not apply a voltage to the TALLY signal pin.
LAN cable
*
(category 5 or above, straight cable), max. 1000 m
[3280 ft]
*
:
Use of an STP (shielded twisted pair) cable is recommended.
Pin
No.
Signal
Pin
No.
Signal
1
GND
5
TXD+
2
TALLY
6
RXD+
3
RXD–
7
—
4
TXD–
8
—
Parts and their functions
Camera unit
18