Panasonic AW-HE130 Operating Instructions - Page 85

Web screen configurations (continued) Frequency This item is selected to switch the frame frequency. Setting value: 59.94Hz / 50Hz • When the frequency is switched, "Format" is set as follows. 59.94Hz 50Hz 1080/59.94p  1080/50p 1080/29.97p  1080/25p 1080/23.98p  1080/25p 1080/59.94i  1080/50i 1080/29.97PsF  1080/25PsF 1080/23.98PsF  1080/25PsF 720/59.94p  720/50p 480/59.94p(i)  576/50p(i) Color Bars Setup This is only enabled when "Frequency" is set to "59.94Hz". Select the color bar setup level (Off: 0.0IRE, On: 7.5IRE) for the VIDEO OUT signal. Setting value: Off 0.0IRE On 7.5IRE zzOther This item's setting is reflected when the Set button is pressed. Install Position "Desktop" or "Hanging" is selected here as the method used to install the unit. Setting value: Desktop Stand-alone installation Hanging Suspended installation • When "Hanging" has been selected, the top, bottom, left and right of the images will be reversed, and up/down/left/right control for panning and tilting will also be reversed. Smart Picture Flip When this is set to [Auto] and the tilt becomes the angle set for [Flip DetectAngle], the image will be flipped in the vertical direction automatically. Setting value: Off Does not flip the image vertically. Auto When the tilt becomes the angle set for [Flip DetectAngle], the image will be flipped in the vertical direction automatically. Flip Detect Angle Set the tilt angle at which the image will be flipped in the vertical direction automatically when [Smart Picture Flip] is set to [Auto]. Setting range: 60° to 120° Preset Speed Table Set the preset speed table (Slow, Fast). During preset playback, presets are performed at [Preset Speed] (1 to 30) values that are based on the table set here. Setting value: Slow Set the preset speed table to slow. Fast Set the preset speed table to fast. Preset Speed Set the pan/tilt movement speed used when recalling camera orientation information registered to the preset memory (30 steps). Setting range: 1 to 30 • When you set large Preset Speed values, the image may sway when the movement stops. • When [Preset Speed Table] is set to [Fast], [Preset Speed] values equivalent to the AW-HE120 will be applied. Preset Scope Selected here are the setting items to be recalled when the contents of the preset memory are regenerated. Setting value: Mode A Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain, white balance adjustment value Mode B Pan, Tilt, Zoom (including digital zoom), Focus, Iris Mode C Pan, Tilt, Zoom (including digital zoom), Focus Freeze During Preset Turn the function for freezing images during preset playback off/on. When this is set to [On], preset playback is performed with a still of the image immediately preceding the start of preset playback being output. The image freeze is released when preset playback is finished. Setting value: Off Do not freezing images during preset playback. On Freeze images during preset playback. Speed With Zoom POS. "Off" or "On" is set here for the function used to adjust the pan-tilt adjustment speed in conjunction with the zoom magnification. When "On" is set, the panning and tilting operations will become slower in the zoom status. This function has no effect during preset operations. Setting value: Off Do not adjust the panning and tilting speed in the zoom status. On The panning and tilting operations will become slower in the zoom status. Focus Mode Select auto or manual mode for the focus adjustment function. Setting value: Auto Always adjust focus automatically. Manual Adjust focus manually. Focus ADJ With PTZ. "Off" or "On" is set here for the function which compensates for out-offocusing when it occurs during panning, tilting or zooming operations. When "Off" is set, adjust the focus as required after zooming or set the focus to the auto mode. This item can be selected only when "Manual" has been selected as the "Focus Mode" setting. Setting value: Off Out-of-focusing is not compensated. On Out-of-focusing is compensated. Digital Zoom "Enable" or "Disable" is set here for the digital zoom function. If zooming is performed toward the Tele end beyond the maximum position when "Enable" has been selected, the digital zoom can be operated continuously. Zooming will stop temporarily at the position where the optical zoom and digital zoom are switched so after it has stopped at this position, proceed with zooming again. When the setting is changed to "Disable" while already in the digital zoom region, the zoom will automatically move to the maximum position of the optical zoom. Setting value: Disable Disable the digital zoom function. Enable Enable the digital zoom function. The digital zoom is set to off when color bars are displayed during digital zooming. Max Digital Zoom Set the maximum digital zoom magnification. Setting value: x2 / x3 / x4 / x5 / x6 / x7 / x8 / x9 / x10 85