Panasonic AW-HE130 Operating Instructions - Page 20
Simultaneous output conditions for each video, format, Parts and their functions continued
View all Panasonic AW-HE130 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
Parts and their functions (continued) Service switch settings SW1 to SW3 (camera address setting switches) Configure the camera address. Set this to AUTO under normal circumstances. When cameras are set to AUTO, addresses will be assigned to the cameras automatically in response operation from the controller in the order in which the cameras were connected. To manually configure the address, set the switches as follows. Address AUTO 1 2 3 4 5 6 7 SW1 OFF ON OFF ON OFF ON OFF ON SW2 OFF ON ON OFF OFF ON ON OFF SW3 OFF ON ON ON ON OFF OFF OFF SW4 (communication format selection switch) Selects the communication format. When this is set to ON, standard serial communication is enabled. When this is set to OFF, Panasonic's proprietary serial communication is enabled. SW5 (maintenance switch) Fixed at OFF. Do not change this switch setting. SW6 (infrared output switch) When this is set to ON, infrared output is enabled. The signal received via the remote control sensor is output from pins 7 and 8 of the connector. Signal output is disabled when this is set to OFF. SW7 (communication baud rate switch) When this is set to ON, the baud rate is 38400 bps. When this is set to OFF, the baud rate is 9600 bps. SW8 (communication connector switch) When this is set to ON, the RS-422 is enabled. When this is set to OFF, the RS-232C is enabled. Simultaneous output conditions for each video format zzSDI/HDMI/VIDEO output Format HD/SDI SD/SDI 1080/59.94p 1080/50p 1080/59.94i 1080/50i 1080/29.97psF 1080/25psF 1080/23.98psF 1080/29.97p 1080/25p 1080/23.98p 720/59.94p 720/50p 480/59.94p 576/50p 480/59.94i 576/50i SDI output HDMI output VIDEO output *1 *1 *1 480/59.94i and 576/50i is output to the VIDEO output regardless of the format setting. zzIP video transmission output (1-/multi-channel display) 1-channel display Resolution 1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90 (non-dependent on SYS format) Frame rate 60Hz 50Hz 1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/ 60 fps*1 1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps*2 *1 60 fps only during H.264 transmission and 1920×1080 or 1280×720 resolution *2 50 fps only during H.264 transmission and 1920×1080 or 1280×720 resolution Setting Resolution Frame 60Hz rate 50Hz Multi-channel display H.264 CH1 1920×1080 / 1280×720 H.264 CH2 1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90 H.264 CH3/ CH4 1280×720 / 640×360 / 320×180 / 160×90 JPEG CH1/ CH2/CH3*3 1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90 60fps 5 fps/15 fps/ 30 fps 5 fps/15 fps/ 30 fps 1 fps/2 fps/ 3 fps/5 fps/ 6 fps/10 fps/ 15 fps/30 fps 50 fps 5 fps/ 12.5 fps/ 25 fps 5 fps/ 12.5 fps/ 25 fps 1 fps/2 fps/ 5 fps/10 fps/ 12.5 fps/ 25 fps *3 Different resolutions must be specified for JPEG CH1 / CH2 / CH3. 20