Sharp VL-WD450U VLWD450U|VLWD650U Operation Manual - Page 25

Attaching and Removing the, Battery Pack

Get Sharp VL-WD450U PDF manuals and user guides View all Sharp VL-WD450U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Preparation Attaching and Removing the Battery Pack Attaching the Battery Pack 1 Make sure that the Power switch is set to OFF. 4 Lower the viewfinder. Power switch 2 Lift up the viewfinder. Removing the Battery Pack 1 Perform steps 1 and 2 above. 2 Press the power source PUSH release button (1), and slide the battery pack up and take it out (2). Power source PUSH release button Power source mounting surface 3 Align the - mark on the side of the battery pack with the q mark on the camcorder (1), and slide the battery pack down completely until it locks into place (2). Cautions: • BEFORE REMOVING THE BATTERY PACK, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE POWER OFF. Removing the battery pack while shooting or during playback may damage the tape by causing it to wrap around the video head drum or may destroy the SmartMedia card, rendering it unreadable and unwritable. • Remove the battery pack from the camcorder if you will not use the camcorder for a long period of time. • Use only SHARP model BT-L221 or BT-L441 battery packs with this camcorder. Use of other batteries may present a risk of fire or explosion. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
10
Preparation
Attaching and Removing the
Battery Pack
Attaching the Battery Pack
1
Make sure that the Power switch is set
to OFF.
Power switch
2
Lift up the viewfinder.
Power source
mounting surface
3
Align the
-
mark on the side of the
battery pack with the
q
mark on the
camcorder (
1
), and slide the battery
pack down completely until it locks into
place (
2
).
4
Lower the viewfinder.
Removing the Battery Pack
1
Perform steps 1 and 2 above.
Power source PUSH
release button
2
Press the power source PUSH release
button (
1
), and slide the battery pack
up and take it out (
2
).
Cautions:
•
BEFORE REMOVING THE BATTERY PACK,
ALWAYS STOP RECORDING OR PLAYBACK
AND TURN THE POWER OFF.
Removing the
battery pack while shooting or during playback
may damage the tape by causing it to wrap
around the video head drum or may destroy the
SmartMedia card, rendering it unreadable and
unwritable.
•
Remove the battery pack from the camcorder if
you will not use the camcorder for a long period
of time.
•
Use only SHARP model BT-L221 or BT-L441
battery packs with this camcorder. Use of other
batteries may present a risk of fire or explosion.