Home » ZyXEL Manuals » Networking » ZyXEL P-870H-53A v2 » Manual Viewer

ZyXEL P-870H-53A v2 User Guide - Page 64

Table 14

Get ZyXEL P-870H-53A v2 PDF manuals and user guides

View all ZyXEL P-870H-53A v2 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Chapter 5 WAN Setup Table 14 WAN Configuration: PPPoE LABEL Authentication Method DESCRIPTION The ZyXEL Device supports PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol). CHAP is more secure than PAP; however, PAP is readily available on more platforms. Use the drop-down list box to select an authentication protocol for outgoing calls. Options are: AUTO - Your ZyXEL Device accepts either CHAP or PAP when requested by this remote node. CHAP - Your ZyXEL Device accepts CHAP only. PAP - Your ZyXEL Device accepts PAP only. Enable Fullcone NAT Dial on Demand Inactivity Timeout Use Static IPv4 Address IPv4 Address Enable PPP Debug Mode Bridge PPPoE Frames Between WAN and Local Ports MSCHAP - Your ZyXEL Device accepts MSCHAP only. MS-CHAP is the Microsoft version of the CHAP. Select this option to enable full cone NAT on the ZyXEL Device. Select this check box when you do not want the connection up all the time and specify an idle time-out in the Inactivity Timeout field. Specify an idle time-out when you select Dial on Demand. The default setting is 0, which means the Internet session will not timeout. A static IPv4 address is a fixed IP that your ISP gives you. A dynamic IP address is not fixed; the ISP assigns you a different one each time you connect to the Internet. Select this if you do not have a dynamic IP address. Enter the static IP address provided by your ISP. Select this option to display PPP debugging messages on the console. Select this option to forward PPPoE packets from the WAN port to the LAN ports and from the LAN ports to the WAN port. In addition to the ZyXEL Device's built-in PPPoE client, you can select this to allow up to ten hosts on the LAN to use PPPoE client software on their computers to connect to the ISP via the ZyXEL Device. Each host can have a separate account and a public WAN IP address. This is an alternative to NAT for application where NAT is not appropriate. Enable IGMP Multicast Proxy Back Next Clear this if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP. Select this check box to have the ZyXEL Device act as an IGMP proxy on this connection. This allows the ZyXEL Device to get subscribing information and maintain a joined member list for each multicast group. It can reduce multicast traffic significantly. Click this button to return to the previous screen. Click this button to continue. 64 P-870H/HW Series User's Guide

Section	Page
P-870H/HW Series	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
User’s Guide	19
Introducing the ZyXEL Device	21
1.1 Overview	21
1.2 Ways to Manage the ZyXEL Device	21
1.3 Good Habits for Managing the ZyXEL Device	22
1.4 Applications for the ZyXEL Device	22
1.4.1 Internet Access	22
1.5 LEDs (Lights)	24
1.6 The RESET Button	25
1.6.1 Using the Reset Button	26
1.7 The WPS WLAN Button (P-870HW Series only)	26
1.7.1 Turn the Wireless LAN Off or On	26
1.7.2 Activate WPS	26
Tutorials	27
2.1 How to Set up a Wireless Network	27
2.1.1 Example Parameters	27
2.1.2 Configuring the AP	27
2.1.3 Configuring the Wireless Client	30
Introducing the Web Configurator	37
3.1 Web Configurator Overview	37
3.1.1 Accessing the Web Configurator	37
3.2 Web Configurator Main Screen	38
3.2.1 Navigation Panel	39
3.2.2 Main Window	41
3.2.3 Status Bar	41
Status Screens	43
4.1 Status Screen	43
4.1.1 WAN Service Statistics	47
4.1.2 Route Info	48
4.1.3 WLAN Station List	49
4.1.4 LAN Statistics	50
4.1.5 Client List	51
Technical Reference	53
WAN Setup	55
5.1 Overview	55
5.1.1 What You Can Do in this Chapter	55
5.2 What You Need to Know	56
5.3 Before You Begin	56
5.4 The Layer 2 Interface Screen	56
5.4.1 Layer 2 Interface Configuration	58
5.5 The Internet Connection Screen	59
5.5.1 WAN Connection Configuration	60
5.6 Technical Reference	71
LAN Setup	77
6.1 Overview	77
6.1.1 What You Can Do in this Chapter	77
6.2 What You Need To Know	78
6.3 The LAN IP Screen	79
6.4 Technical Reference	81
Wireless LAN	85
7.1 Overview	85
7.1.1 What You Can Do in this Chapter	85
7.2 What You Need to Know	86
7.3 Before You Begin	88
7.4 The General Screen	89
7.4.1 No Security	90
7.4.2 WEP Encryption	91
7.4.3 WPA(2)-PSK	93
7.4.4 WPA(2) Authentication	94
7.4.5 MAC Filter	95
7.4.6 Adding a New MAC Filtering Rule	97
7.5 The More AP Screen	97
7.5.1 More AP Edit	98
7.6 The WPS Screen	98
7.7 The WPS Station Screen	100
7.8 The WDS Screen	101
7.9 The Advanced Setup Screen	103
7.10 Technical Reference	105
7.10.1 Wireless Network Overview	105
7.10.2 Additional Wireless Terms	106
7.10.3 Wireless Security Overview	106
7.10.4 WiFi Protected Setup	109
Network Address Translation (NAT)	117
8.1 Overview	117
8.1.1 What You Can Do in this Chapter	117
8.2 What You Need to Know	117
8.3 The Port Forwarding Screen	118
8.3.1 The Port Forwarding Edit Screen	120
8.4 The Address Mapping Screen	121
8.4.1 The Address Mapping Rule Edit Screen	123
8.5 The Trigger Port Screen	124
8.5.1 Trigger Port Configuration	126
8.6 The DMZ Host Screen	128
8.7 The ALG Screen	128
8.8 Technical Reference	129
MAC Filter	131
9.1 Overview	131
9.1.1 What You Can Do in this Chapter	131
9.2 The MAC Filter Screen	131
9.2.1 Creating MAC Filtering Rules	133
Firewall	135
10.1 Overview	135
10.1.1 What You Can Do in this Chapter	135
10.2 What You Need to Know	135
10.3 The Firewall Screen	136
10.3.1 Creating Incoming Firewall Rules	138
Certificate	141
11.1 Overview	141
11.1.1 What You Can Do in this Chapter	141
11.2 What You Need to Know	141
11.3 The Local Certificates Screen	142
11.3.1 Create Certificate Request	143
11.3.2 Import Certificate	144
11.3.3 Certificate Details	146
11.3.4 Load Signed Certificate	148
11.4 The Trusted CA Screen	149
11.4.1 View Trusted CA Certificate	151
11.4.2 Import Trusted CA Certificate	152
Static Route	153
12.1 Overview	153
12.1.1 What You Can Do in this Chapter	153
12.2 The Static Route Screen	154
12.2.1 Static Route Edit	155
Policy Forwarding	157
13.1 Overview	157
13.1.1 What You Can Do in this Chapter	157
13.2 The Static Route Screen	157
13.2.1 Policy Forwarding Setup	158
RIP	161
14.1 Overview	161
14.1.1 What You Can Do in this Chapter	161
14.2 The RIP Screen	161
Quality of Service (QoS)	163
15.1 Overview	163
15.1.1 What You Can Do in this Chapter	163
15.2 What You Need to Know	164
15.3 The Quality of Service General Screen	164
15.4 The Queue Setup Screen	166
15.4.1 Adding a QoS Queue	167
15.5 The Class Setup Screen	168
15.5.1 QoS Class Edit	170
15.6 The QoS Monitor Screen	174
15.7 Technical Reference	175
Dynamic DNS Setup	177
16.1 Overview	177
16.1.1 What You Can Do in this Chapter	177
16.2 What You Need To Know	177
16.3 The Dynamic DNS Screen	178
Remote Management	179
17.1 Overview	179
17.1.1 What You Can Do in this Chapter	179
17.2 The TR-069 Screen	179
17.3 The TR-064 Screen	181
17.4 The Service Control Screen	182
17.5 The IP Address Screen	183
17.5.1 Adding an IP Address	184
Universal Plug-and-Play (UPnP)	185
18.1 Overview	185
18.1.1 What You Can Do in this Chapter	185
18.2 What You Need to Know	185
18.3 The UPnP Screen	186
18.4 Installing UPnP in Windows Example	187
18.5 Using UPnP in Windows XP Example	191
Parental Control	199
19.1 Overview	199
19.1.1 What You Can Do in this Chapter	199
19.2 The Time Restriction Screen	199
19.2.1 Adding a Schedule	200
19.3 The URL Filter Screen	201
19.3.1 Adding URL Filter	202
Interface Group	203
20.1 Overview	203
20.1.1 What You Can Do in this Chapter	203
20.2 The Interface Group Screen	203
20.2.1 Interface Group Configuration	204
20.2.2 Interface Grouping Criteria	206
System Settings	209
21.1 Overview	209
21.1.1 What You Can Do in this Chapter	209
21.2 The General Screen	209
21.3 The Time Setting Screen	210
Logs	213
22.1 Overview	213
22.1.1 What You Can Do in this Chapter	213
22.2 The View Log Screen	213
22.3 The Log Settings Screen	214
Tools	217
23.1 Overview	217
23.1.1 What You Can Do in this Chapter	217
23.2 The Firmware Screen	218
23.3 The Configuration Screen	220
23.4 The Restart Screen	222
Diagnostic	225
24.1 Overview	225
24.1.1 What You Can Do in this Chapter	225
24.2 What You Need to Know	225
24.3 The General Diagnostic Screen	226
24.4 The 802.1ag Screen	227
Troubleshooting	229
25.1 Power, Hardware Connections, and LEDs	229
25.2 ZyXEL Device Access and Login	230
25.3 Internet Access	231
Product Specifications	235
26.1 Hardware Specifications	235
26.2 Firmware Specifications	235
26.3 Wireless Features (for P-870HW Series only)	238
Setting Up Your Computer’s IP Address	241
Pop-up Windows, JavaScript and Java Permissions	271
IP Addresses and Subnetting	281
Wireless LANs	293
Common Services	309
Open Software Announcements	313
Legal Information	325

Match case Limit results 1 per page

Chapter 5 WAN Setup

P-870H/HW Series User’s Guide

Authentication

Method

The ZyXEL Device supports PAP (Password Authentication Protocol)

and CHAP (Challenge Handshake Authentication Protocol). CHAP is

more secure than PAP; however, PAP is readily available on more

platforms.

Use the drop-down list box to select an authentication protocol for

outgoing calls. Options are:

AUTO

- Your ZyXEL Device accepts either CHAP or PAP when

requested by this remote node.

CHAP

- Your ZyXEL Device accepts CHAP only.

PAP

- Your ZyXEL Device accepts PAP only.

MSCHAP

- Your ZyXEL Device accepts MSCHAP only. MS-CHAP is the

Microsoft version of the CHAP.

Enable Fullcone

NAT

Select this option to enable full cone NAT on the ZyXEL Device.

Dial on Demand

Select this check box when you do not want the connection up all the

time and specify an idle time-out in the

Inactivity Timeout

field.

Inactivity

Timeout

Specify an idle time-out when you select

Dial on Demand

. The

default setting is 0, which means the Internet session will not timeout.

Use Static IPv4

Address

A static IPv4 address is a fixed IP that your ISP gives you. A dynamic

IP address is not fixed; the ISP assigns you a different one each time

you connect to the Internet. Select this if you do not have a dynamic

IP address.

IPv4 Address

Enter the static IP address provided by your ISP.

Enable PPP

Debug Mode

Select

this option to display PPP debugging messages on the console.

Bridge PPPoE

Frames Between

WAN and Local

Ports

Select this option to forward PPPoE packets from the WAN port to the

LAN ports and from the LAN ports to the WAN port.

In addition to the ZyXEL Device's built-in PPPoE client, you can select

this to allow up to ten hosts on the LAN to use PPPoE client software

on their computers to connect to the ISP via the ZyXEL Device. Each

host can have a separate account and a public WAN IP address.

This is an alternative to NAT for application where NAT is not

appropriate.

Clear this if you do not need to allow hosts on the LAN to use PPPoE

client software on their computers to connect to the ISP.

Enable IGMP

Multicast Proxy

Select this check box to have the ZyXEL Device act as an IGMP proxy

on this connection. This allows the ZyXEL Device to get subscribing

information and maintain a joined member list for each multicast

group. It can reduce multicast traffic significantly.

Back

Click this button

to return to the previous screen.

Click this button to continue.

Table 14

WAN Configuration: PPPoE

LABEL

DESCRIPTION