HP StorageWorks 1606 HP StorageWorks 8GB SAN Switch hardware reference guide (
HP StorageWorks 1606 - Extension SAN Switch Manual
View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP StorageWorks 1606 manual content summary:
- HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 1
document provides information on installing, configuring, and maintaining the 8-Gb SAN family of HP StorageWorks Fibre Channel switches. This document is intended for system administrators and technicians with knowledge of SANs and HP StorageWorks Fibre Channel switches. Part number: 5697-0291 Fifth - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 2
as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Acknowledgements Microsoft® and Windows® are registered trademarks of Microsoft Corporation. Warranty For information about HP StorageWorks product warranties, see the - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 3
8/8 and 8/24 SAN Switch ports 13 Enabling E_Ports on the 8/8 SAN Switch 14 8/40 SAN Switch features ...14 Port side of the 8/40 SAN Switch 14 Nonport side of the 8/40 SAN Switch 15 Activating additional 8/40 SAN Switch ports 15 8/80 SAN Switch features ...16 Port side of the 8/80 SAN Switch 16 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 4
the 1606 Extension SAN Switch 54 FCIP and Fibre Channel routing services configuration 54 Verifying switch operation 55 8-Gb SAN Switch LEDs ...56 8/8 and 8/24 SAN Switch LEDs 56 8/40 SAN Switch LEDs ...57 8/80 SAN Switch LEDs ...58 Port side LED activity for the 8/80 SAN Switch 59 Nonport side - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 5
...87 FCoE Converged Network Switch data flow latency 91 Fibre Channel port specifications 91 POST and boot specifications ...91 POST ...91 Boot ...92 Supported HBAs and CNAs ...92 5 Support and other resources 93 HP technical support ...93 Subscription service ...93 Documentation feedback ...93 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 6
Estonian notice ...102 Finnish notice ...102 French notice ...103 German notice ...103 Greek notice ...103 Hungarian notice ...104 Italian notice ...104 Latvian notice ...104 Lithuanian notice ...105 Polish notice ...105 Portuguese notice ...105 Slovakian notice ...106 Slovenian notice ...106 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 7
device in an HP System/e Rack 43 24 Connecting the serial cable 45 25 Encryption configuration 54 26 Identifying 8/8 and 8/24 SAN Switch LEDs 56 27 Identifying 8/40 SAN Switch port side LEDs 57 28 Identifying 8/40 SAN Switch nonport side LEDs 57 29 Identifying 8/80 SAN Switch port side LEDs - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 8
an SFP in the upper row of port slot 73 35 Nonport side LEDs 74 36 8/80 and Encryption SAN Switch fan assemblies on the nonport side 76 37 Inserting the fan assembly in the 8/80 SAN Switch 78 38 Installing a power supply in the 8/80 or Encryption SAN Switch 79 39 Class 1 laser product label 98 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 9
ranges for the 8/40 SAN Switch 87 26 Laser data transmission ranges for the 8/80 SAN Switch 88 27 Laser data transmission ranges for the Encryption SAN Switch and FCoE Converged Network Switch ...89 28 Laser data transmission ranges for the 1606 Extension SAN Switch Fibre Channel ports ...90 29 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 10
31 Document conventions 95 10 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 11
• HP StorageWorks 8/40 SAN Switch-Ships with 24 ports activated and includes a Full Fabric license. It includes Advanced Web Tools, Advanced Zoning, and EGM as standard software components. • HP StorageWorks 8/40 Power Pack+ SAN Switch-Ships with 24 ports activated and includes a Full Fabric license - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 12
Fibre Channel ports, 24 active CEE ports, base software (Full Fabric, Advanced Fabric OS, Advanced Web Tools, and Advanced Zoning), and Power Pack+ software (ISL Trunking, Advanced Performance Monitor, and Fabric Watch). • HP StorageWorks 1606 Extension SAN Switch-Ships with 6 Fibre Channel SFP - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 13
7). Additionally, the 8/24 SAN Switch model integrates 16 licensed ports (ports 0 through 15). To enable additional ports, you must purchase and install the HP Storage Works 8/8 and 8/24 SAN Switch 8-Gb 8-port Upgrade LTU (part number T5518A): • For the 8/8 SAN Switch-To enable ports 8 through 15 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 14
activating Port Upgrade licenses, page 25. Enabling E_Ports on the 8/8 SAN Switch The 8/8 SAN Switch model requires that you purchase the HP StorageWorks Full Fabric Upgrade License (part number T4261A) to enable E_Ports (the 8/24 SAN Switch ships with the Full Fabric license installed). By default - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 15
8/40 SAN Switch ports By default, the 8/40 SAN Switch model integrates 24 licensed ports (ports 0 through 23). To enable additional ports, you must purchase and install the HP Storage Works 8/40 SAN Switch 8-Gb 8-port Upgrade LTU (part number T5519A): 8-Gb SAN Switch Hardware Reference Guide 15 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 16
enable ports 32 through 40, you must purchase and install a second upgrade license. See Installing and activating Port Upgrade licenses, page 25. 8/80 SAN Switch features • Provides the EZSwitch Setup Wizard for easy setup and basic configuration. • Integrates 1, 2, 4, and 8 Gb/s autosensing Fibre - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 17
port 7. FC ports 0-7 8. FC ports 8-15 9. FC ports 16-23 10. FC ports 24-31 11. FC ports 32-38 12. FC ports 40-47 13. FC ports 48-55 14. FC ports 56-63 15. FC ports 64-71 16. FC ports 72-79 Figure 4 Port side view-8/80 SAN Switch . Nonport side of the 8/80 SAN Switch and the Encryption SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 18
additional 8/80 SAN Switch ports By default, the 8/80 SAN Switch model integrates 48 licensed ports (ports 0 through 47). To enable additional ports, you must purchase and install the HP StorageWorks 8/80 SAN Switch 8-Gb 16-port Upgrade LTU (part number T5520A): • To enable ports 48 through - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 19
of 96 Gb/s of encryption bandwidth. The front-end user ports in the basic, first, and second levels of encryption bandwidth remain as 32 ports at 8 Gb/s Fibre Channel. Port side of the Encryption SAN Switch The port side of the Encryption SAN Switch includes the status and power LEDs, smart card - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 20
an RJ-45 Ethernet management port and EZSwitch Setup, which supports switch IP address discovery and configuration • Integrates a USB port that provides storage for firmware updates, as well as supportsave command output and configuration uploads and downloads • Provides two hot-swappable, redundant - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 21
A fully licensed 1606 Extension SAN Switch has the following features: • FCIP capability • Includes up to eight FCIP tunnels. • Each FCIP tunnel is represented and managed as a VE_Port. • Fibre Channel Routing Services can be used over the FCIP link. 8-Gb SAN Switch Hardware Reference Guide 21 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 22
connected through FCIP merge if the ports are configured as VE_Ports, and do not merge if one end of the connection is configured as a VEx_Port. If VE_Ports are used in a Fibre Channel Routing Services backbone fabric configuration, then the backbone fabric merges but the EX_Ports attached to - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 23
optionally licensed features. Table 1 Comparison of 1606 Extension SAN Switch features Feature Base product With upgrade license Number of Fibre Channel ports 4 16 Number of GbE ports 2 6 Fibre Channel Routing between remote fabrics for fault isolation Yes1 Yes1 FCIP Tunnel Yes Yes - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 24
only) 4. GbE ports: ge0-ge5 (SFP) Figure 10 Port numbering on the 1606 Extension SAN Switch . A fully licensed 1606 Extension SAN Switch can have two trunking groups. Group 1 consists of Fibre Channel ports 0-7, and group 2 consists of Fibre Channel ports 8-15. 24 HP StorageWorks 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 25
SAN Switch . Installing and activating Port Upgrade licenses 1. Use the portshow command to verify the number of ports licensed on your switch. The port status output indicates Started and Licensed for enabled ports. For more information on this command, see the Fabric OS Command Reference Manual - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 26
ISL Trunking groups All 8-Gb SAN Switch models support ISL Trunking as an optional, licensed feature for FC ports. When this feature is enabled, trunked groups of up to eight contiguous ports are created. For example, the Fibre Channel ports on the SAN Switch are numbered from left to right and - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 27
the Fabric OS Administrator's Guide for the firmware version you are running. Supported SFP transceiver options Table 2 lists the only SFPs supported in your HP StorageWorks 8-Gb SAN Switches. Table 2 Supported SFP transceiver options Switch product Port type Option Part number Fibre Channel - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 28
product QuickSpecs, which can be accessed from the HP website: http://h18006.www1.hp.com/storage/networking/b_switches/san/index.html • HP StorageWorks Full Fabric Upgrade License • HP StorageWorks 8/8 and 8/24 SAN Switch 8-Gb 8-port Upgrade LTU • HP StorageWorks 8/80 SAN Switch 8-Gb 16-port Upgrade - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 29
LTU • HP StorageWorks Power Pack Upgrade • SAO • HP B-series 24-40 Port SAN Switch Integrated Routing LTU (purchase for 8/40 SAN Switch only) 8-Gb SAN Switch hardware options Table 3 lists the optional hardware kits. Table 3 Optional hardware kits Hardware kit Order number HP StorageWorks 2-Gb - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 30
Hardware kit 50 m LC-SC multi-mode FC cable Order number 221691-B27 NOTE: For the latest information on hardware and software components, see the B-series Switches section of the HP Storage Networking website: http://www.hp.com/go/san. 30 HP StorageWorks 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 31
and instructions to install and configure an 8-Gb SAN Switch. Shipping carton contents Figure 13 and Table 4 identify shipping carton contents for a typical 8-Gb SAN Switch. The shipping configuration for your model can vary. 1. Accessory kit 2. Rails 3. Switch Figure 13 8/40 SAN Switch shipping - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 32
kit, containing the following items: • HP StorageWorks product documentation: • HP StorageWorks 8-Gb SAN Switch Quick Start Instructions • HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions • Read Me First • Safety Guides • User License • Warranty • A serial cable, approximately - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 33
and managed in a variety of ways: for example, using cable channels on the sides of the cabinet or patch panels to minimize cable management. Before installing the switch, plan for cable management based on the following HP recommendations: • Leave enough space to allow for the fact that the - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 34
must meet specific requirements, as described in the Fabric OS Administrator's Guide. • For easier maintenance, label the fiber switch on a flat, sturdy surface. 5. Apply power to the switch as described in "Powering on the 8-Gb SAN Switch" on page 44. 34 Installing and configuring an 8-Gb SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 35
See "Setting the switch IP address" on page 46. Installing the switch using the SAN Switch Rack Mount Kit The SAN Switch Rack Mount Kit is supplied with your 8-Gb SAN Switch. Use the SAN Switch Rack Mount Kit for installations in the following HP StorageWorks custom racks only: • HP 9000 Series Rack - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 36
8/24, 8/40, 8/80 SAN Switches, FCoE Converged Network Switch, Encryption SAN Switch, and 1606 Extension SAN Switch NOTE: All devices require 10 screws except for the Encryption SAN Switch, 1606 Extension SAN Switch, and FCoE Converged Network Switch, which require only 6 screws. 36 Installing and - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 37
of the rack. This allows air to enter the front of the rack and exit from the rear. To install the device in a rack: 1. Verify that the required parts and hardware are available. (See Table 5.) 2. Choose a mounting location for the device in the rack. 8-Gb SAN Switch Hardware Reference Guide 37 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 38
rear mounting brackets (HP 10000 Series rack) . Figure 15 Installing the rear mounting brackets (HP System/e rack) . NOTE: The SAN Switch Rack Mount Kit contains rails labeled Left and Right to designate the left side and right side of the cabinet. 38 Installing and configuring an 8-Gb SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 39
right rail. Then, install two #10-32 x 1/2-inch Phillips panhead screws with captive star lock washers and two #10 adapter washers in the upper and lower holes on the left rail. (See Figure 17.) Figure 17 Assembling the outer rails (HP 10000 Series rack) . 8-Gb SAN Switch Hardware Reference Guide 39 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 40
8/40 or 8/80 SAN Switches, use the screw holes marked 16, as shown in Figure 20 on page 41. • To attach the inner rails to the FCoE Converged Network Switch, Encryption SAN Switch, or 1606 Extension SAN Switch, use two screw holes marked R and one screw hole marked 16. 40 Installing and configuring - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 41
rails requires ten screws. This figure also applies to the 8/8, 8/24, 8/40, and 8/80 SAN Switches. Figure 19 Securing the inner rails to an MP Router . Figure 20 Securing the inner rails to the 4/64 SAN Switch . NOTE: For factory integration only, tighten the #8-32 x 5/16-inch Phillips panhead SEMS - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 42
one of the following devices, install the plenum included in the switch accessory kit: • 8/8 SAN Switch • 8/24 SAN Switch See "Installing the plenum" on page 42 for complete installation instructions. If you are installing a different device, see "Securing the switch to the outer rails" on - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 43
racks) . Figure 23 Securing the device in an HP System/e Rack . 3. Tighten the hex nuts installed in step 4 of Installing the HP SAN Switch Rack Mount Kit in your HP custom rack, page 36. (See Figure 16, page 39.) This completes the rack mount procedure. 8-Gb SAN Switch Hardware Reference Guide 43 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 44
are going to use the 8-Gb SAN Switch in a single-switch setup, you can use EZSwitch Setup to complete the basic configuration. For more information, see the EZSwitch Setup CD or HP StorageWorks 8-Gb SAN Switch Quick Start Instructions, included with your 8-Gb SAN Switch. If you do not want to use - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 45
All basic configuration tasks require a serial connection. 1. Connect the serial cable to an RS-232 serial port on the workstation, as shown in Figure 24. Figure 24 shows the 8/40 SAN Switch; however, the procedure is similar for all SAN Switches. NOTE: If the serial port on the workstation - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 46
string at the prompt: tip /dev/ttya -9600 Setting the switch IP address You can configure the 8-Gb SAN Switch with a static IP address, or you can use a DHCP server to set the IP address. DHCP is enabled by default. The 8-Gb SAN Switch supports both IPv4 and IPv6. DHCP When using DHCP, the 8-Gb - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 47
by the previous switch, if it is still available: Domain: (1 ..239) [1] 3 6. Complete the remaining prompts or press Ctrl+D to accept the remaining settings without completing all the prompts. 7. Re-enable the switch by entering the switchenable command. 8-Gb SAN Switch Hardware Reference Guide 47 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 48
are in one time zone, you can keep the time zone setup at the default setting. • System services that have already started reflect the time zone changes only after the next reboot. • Time zone settings persist across failover for high availability. 48 Installing and configuring an 8-Gb SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 49
tstimezone -6,0 For Eastern Standard Time, enter tstimezone -5,0 The default time zone for switches is UTC, which is 8 hours ahead of Pacific Standard Time. To determine the tstimezone command parameter for other U.S. time zones, see Table 7 on page 50. 8-Gb SAN Switch Hardware Reference Guide 49 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 50
primary FCS switch. Changes to the clock server value on the principal or primary FCS switch are propagated to all switches in the fabric. For more information on using an NTP server, and IPv6 considerations, see the Fabric OS Administrator's Guide. 50 Installing and configuring an 8-Gb SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 51
information about the fabric. Backing up the configuration HP recommends regular backups to ensure that a recent configuration is available. To back up the switch configuration to an FTP server: 1. Issue the configupload command. 2. Follow the prompts. 8-Gb SAN Switch Hardware Reference Guide 51 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 52
to the server, making it available for downloading to a replacement switch, if necessary. For instructions on backing up the configuration, see the Fabric OS Administrator's Guide. Changing the switch name and chassis name Changing the switch and chassis names is important for accurate tracking - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 53
HP StorageWorks 8/40 and 8/80 SAN Switches, the Encryption SAN Switch the FCoE Converged Network Switch, and the 1606 Extension SAN Switch. Configuring the Encryption SAN Switch NOTE: For procedures to configure the encryption functions, including HP Secure Key Manager information, see the Fabric - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 54
Channel Routing Services feature before enabling the ports. The GbE ports can be used only after you have configured FCIP and enabled the VE_Ports. For instructions on configuring the Fibre Channel Router ports and GbE ports on the 1606 Extension SAN Switch, see the Fabric OS Administrator's Guide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 55
SAN Switch: 1. Check the LEDs to verify that all components are functional (see "Port side LED activity for the 1606 Extension SAN Switch" on page 67). 2. Execute the portcfgpersistentenable command to activate the FC ports BB Fabric ID: 1 Index Port Address SAN Switch Hardware Reference Guide 55 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 56
about the fabric. 8-Gb SAN Switch LEDs System activity and status can be determined through the activity of the LEDs on the switch. The LED states are as follows: • No light • Steady light • Flashing light The LEDs are either green or amber. 8/8 and 8/24 SAN Switch LEDs 8/8 and 8/24 SAN Switch LEDs - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 57
power (bottom) 2. Ethernet port status LEDs (green/amber) 3. FC port status (port 9) Figure 27 Identifying 8/40 SAN Switch port side LEDs . 1. Power supply 1 status LED 2. Power supply 2 status LED Figure 28 Identifying 8/40 SAN Switch nonport side LEDs . 8-Gb SAN Switch Hardware Reference Guide 57 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 58
Ethernet link LED 6. FC port status LED (port 0) 7. FC port status LED (port 4) 8. FC ports (0 through 7) 9. FC ports (48 through 55) 10. FC port status LED (port 52) 11. FC port status LED (port 48) 12. Console port 13. System power LED Figure 29 Identifying 8/80 SAN Switch port side LEDs . 58 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 59
assembly #2 status LED 10. Fan Assembly #3 status LED Figure 30 Identifying 8/80 SAN Switch nonport side LEDs . Port side LED activity for the 8/80 SAN Switch Table 8 describes LEDs and recommended actions. Table 8 8-Gb SAN Switch port side LED patterns LED name Power status LED color No light - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 60
. Re-enable the port us- intervals) command. ing the portenable command. Fast flashing amber Port is faulty. (flashing in halfsecond intervals) Check the management interface and the error log for details on the cause of status. Contact your switch service provider. 60 Managing the 8-Gb SAN - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 61
failed. • The fan FRU was disabled by the user. NOTE: When the switch is first powered on, the fan status LED will show amber until POST has completed. Do the following: • Verify the fan FRU is enabled (use the fanenable command). • Replace the fan FRU. 8-Gb SAN Switch Hardware Reference Guide 61 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 62
Port side LED activity for the Encryption SAN Switch Table 10 describes LEDs and recommended actions. Table 10 Encryption SAN Switch the system console. 4. Contact your service provider. Power status No light detected. • The switch is initializing. • A connected device is configured in an offline - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 63
enable the port us- command. ing the portenable command. Fast flashing amber SFP or port is faulty. (on 1/2 second, then off 1/2 second) Replace the SFP. Reset the port. No light Indicates one of the following: • Power supply FRU is switched FRU. 8-Gb SAN Switch Hardware Reference Guide 63 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 64
disabled by the user. NOTE: When the switch is first powered on, the fan status LED shows amber until POST has completed. Do one of the following: • Verify that the fan FRU is seated correctly. • Verify that the fan FRU is enabled (use the fanenable command). • Replace the fan FRU. Port side LED - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 65
cause of the status. Contact your switch service provider. Port speed is 10 Mb/s. No action required. Port speed is 100/1000 Mb/s. No installed correctly and the cable is connected correctly. Receiving light or carrier, but not online No action required. 8-Gb SAN Switch Hardware Reference Guide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 66
enable the port using the portenable command. Fast blinking amber Port failure (1/2 second) Check the management interface and the error log for details on the cause of the failure. Contact HP technical support side LEDs on the FCoE Converged Network Switch . 66 Managing the 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 67
switch. Table 12 FCoE Converged Network Switch switch is . • Verify the switch is powered on. enabled (use the fanenable command). • Replace the fan FRU. Port side LED activity for the 1606 Extension SAN Switch SAN Switch. Figure 33 shows the LEDs on the port side of the 1606 Extension SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 68
Port 0 status LED 10. Port 4 status LED 11. Port 8 status LED 12. GbE copper port 13. GbE port 0 Fault (FLT) LED 14. GbE port 0 status/activity LED 15. GbE optical port 16. GbE dual-color optical port LED Figure 33 Port side LEDs on the 1606 Extension SAN Switch . 68 Managing the 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 69
or cable) is detected. • Device may be initializing. • Connected device is configured in an offline state. Verify that the power LED is on. Verify the SFP and cable. Verify that the device is not initializing. Verify the status of the connected device. 8-Gb SAN Switch Hardware Reference Guide 69 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 70
Port is online and frames are flowing through the port. No action required. Green off, steady amber Port is faulty. Reset the switch from the workstation. If the problem persists, use the other copper port or the optical ports, or return the switch for repair. 70 Managing the 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 71
the Fabric OS Administrator's Guide or the Web Tools Administrator's Guide. b. ports in the switch is OK. • If you are using Web Tools, select Port Admin or Status to display information about the ports. • If you are using the CLI, use the diagshow command. 8-Gb SAN Switch Hardware Reference Guide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 72
sections. Installing an SFP The 8-Gb SAN Switches support only HP-branded SFPs. For ordering information, see "Supported SFP transceiver options" on page 27. If you use an unqualified SFP, the switchshow command output will show the port in an Mod_Inv state. Additionally, the firmware logs the - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 73
tests, see the Brocade Fabric OS Troubleshooting and Diagnostics Guide. Installing Field-Replaceable Units This section lists FRUs and provides FRU installation procedures. 8/8 SAN Switch and 8/24 SAN Switch FRU units No components in the 8/8 SAN Switch and 8/24 SAN Switch are field replaceable. If - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 74
8/40 SAN, FCoE Converged Network, and 1606 Extension SAN Switch FRU units Replace the power supply and one at a time. They are identical and fit into any fan slot. Fabric OS identifies the fan assemblies as follows (viewing the switch from the nonport side): • Fan assembly 2 is on the left. • - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 75
the fan FRU is enabled and the FRU is faulty it should be replaced. Replacing the 8/40 SAN Switch power supply and fan assembly CAUTION: Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications. There are no user-serviceable parts inside the power - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 76
using the fanshow command from the CLI. 8/80 SAN Switch and Encryption SAN Switch FRU units Replace the following FRUs as required: • Fan assembly • Power supply The 8/80 SAN Switch and Encryption SAN Switch integrate three fan assemblies (see Figure 36). Fabric OS identifies the fans from left to - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 77
approximately two minutes. You will need: • 8/80 SAN Switch or Encryption SAN Switch • New fan FRU assembly • Phillips-head screwdriver #1 CAUTION: The 8/80 and Encryption SAN Switches use two power cords. Disconnect both power cords before servicing. To replace a fan assembly: 1. Use a Phillips - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 78
5. Handle 6. Nonport side Figure 37 Inserting the fan assembly in the 8/80 SAN Switch . Replacing an 8/80 SAN Switch or Encryption SAN Switch power supply CAUTION: If a power supply fails, leave the power supply in the switch until it can be replaced. Maintain both power supplies in operational - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 79
Status LED 3. Handle 4. Captive screw 5. AC power switch 6. Power supply Figure 38 Installing a power supply in the 8/80 or Encryption SAN Switch . 4. Using a Phillips screwdriver, unscrew the captive screw 38, with the AC power receptacle on the left. 8-Gb SAN Switch Hardware Reference Guide 79 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 80
fabric topology, check port status, and debug the switch. Table 16 lists the management tools available. When running IP over FC, these management tools must be supported by both HBA and HBA drivers. For a list of supported HBAs, see the HP StorageWorks SAN Design Reference Guide: http:// www.hp - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 81
Center Fabric Manager Enterprise User guide or the Brocade Data Center Fabric Manager Professional User guide. Ethernet or serial connection In-band support IP over FC IP over FC IP over FC IP over FC Native in-band interface (over HBA only) IP over FC 8-Gb SAN Switch Hardware Reference Guide 81 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 82
82 Managing the 8-Gb SAN Switches - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 83
the physical dimensions for the SAN Switches. Table 17 8-Gb SAN Switch physical dimensions Property 8/8 and 8/24 8/40 SAN SAN Switches Switch Height 4.29 cm nl (1.69 inches) 1U = 4.3 cm nl (1.7 inches) 8/80 SAN Switch 2U = 8.6 cm nl (3.4 inches) Encryption SAN Switch FCoE nl Converged nl - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 84
24 and 8/40 SAN Switch memory Memory type Main Memory (SDRAM) Boot Flash Compact Flash Install memory 512 MB 8/40 SAN Switch only: 4 MB 1 GB Table 19 lists the 8/80 SAN Switch, Encryption SAN Switch, and FCoE Converged Network Switch memory specifications. Table 19 8/80 SAN Switch, Encryption SAN - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 85
(when rack mounted) Requirements 8/8 and 8/24 SAN Switches-A minimum of 24 cu ft/min of airflow is available to the air intake vents on the nonport side of the switch. 8/40, 8/80, Encryption, and 1606 Extension SAN Switches-Air flows from the nonport side to the port side. A minimum airflow of 79 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 86
the port side of the switch. Table 23 lists the power supply specifications. Table 23 Power supply specifications Specification Description Inlet C13 Maximum output from each power supply 8/8 and 8/24 SAN Switches: 75 W, with fans operating 8/40 SAN Switch: 125 W, with fans operating 8/80 SAN - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 87
N/A 10 km (6.2 miles) 40 km (24.8 miles) 10 km (6.2 miles) N/A 10 km (6.2 miles) N/A 10 km (6.2 miles) without an HP Extended Fabrics license 50 to 100 km with an HP Extended Fabrics license 40 km (24.8 miles) 4 Gb/s 50 150 m (492 ft) N/A N/A 8-Gb SAN Switch Hardware Reference Guide 87 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 88
40 SAN Switch, up to 500 km at 1 Gb/s is supported when using a long distance transport system such as DWDM. Table 26 Laser data transmission ranges for the 8/80 SAN Switch Port (6.2 miles) without an HP Extended Fabrics license 50 to 100 km with an HP Extended Fabrics license 80 km (50 miles) 4 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 89
80 SAN Switch, up to 500 km at 1 Gb/s is supported when using a long-distance transport system such as DWDM. Table 27 Laser data transmission ranges for the Encryption SAN Switch and FCoE Converged Network Switch Port N/A N/A N/A N/A 10 km (6.2 miles) 8-Gb SAN Switch Hardware Reference Guide 89 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 90
) NOTE: For the Encryption SAN Switch and FCoE Converged Network Switch, up to 500 km at 1 Gb/s is supported when using a long-distance transport system such as DWDM. Table 28 Laser data transmission ranges for the 1606 Extension SAN Switch Fibre Channel ports Port speed 1 Gb/s Cable size nl - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 91
Data flow latency type FC port to FC port CEE port to CEE port (same ASIC) CEE port to CEE port (different ASIC) FCoE to FC Size in nanoseconds +/- 700 ns 570 ns 1,050 ns 1,670 ns Fibre Channel port specifications The Fibre Channel ports in the 8-Gb SAN Switch are compatible with SWL, LWL, and - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 92
routing tables • Enables normal port operation Supported HBAs and CNAs NOTE: CNAs apply to the FCoE Converged Network Switch only. For a list of HBAs that have been tested and are known to work with the SAN switches, see the latest version of the HP StorageWorks SAN Design Reference Guide, at http - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 93
Brocade Fabric OS Administrator's Guide 6.3.0 • Brocade Fabric OS Encryption Administrator's Guide • Brocade Converged Enhanced Ethernet Administrator's Guide You can find these documents on the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals 8-Gb SAN Switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 94
click HP StorageWorks DC SAN Director Switches to access the Manuals web page. The Brocade SAN Glossary provides definitions for SAN-related terminology used throughout this document. To access the glossary, see http://h20000.www2.hp.com/bc/docs/support/ SupportManual/c01429405/c01429405.pdf?jumpid - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 95
Convention Blue text: Table 31 Blue, underlined text: http://www.hp.com Bold text Italic text Monospace text Monospace, italic text Monospace, or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. 8-Gb SAN Switch Hardware Reference Guide 95 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 96
CSR programs allow you to repair your StorageWorks product. If a CSR part needs replacing, HP ships the part directly to you so that you can install it at your convenience. Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a repair can be accomplished by - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 97
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. The end user of this product - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 98
no user-serviceable components HP authorized service technicians to repair the laser device. Certification and classification information This product contains a laser internal to the FO transceiver for connection to the Fibre Channel communications port surface of the HP supplied laser device - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 99
numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union regulatory notice Japanese notice 8-Gb SAN Switch Hardware Reference Guide 99 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 100
. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product. For more information about battery replacement or proper disposal, contact an HP authorized service provider. WARNING! Your switch contains an internal lithium manganese dioxide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 101
of power cord to use, contact an HP authorized service provider. NOTE: Route power cords so by users in private service, or the shop where you purchased the product. Dutch notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie 8-Gb SAN Switch Hardware Reference Guide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 102
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 103
de recyclage des appareils mis au rebut, veuillez contacter les autorités locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous avez acheté ce produit. äft, in dem Sie das Gerät erworben haben. Greek notice 8-Gb SAN Switch Hardware Reference Guide 103 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 104
Hungarian notice Italian notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 105
o ambiente e a saúde das pessoas. Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido. 8-Gb SAN Switch Hardware Reference Guide 105 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 106
Slovakian notice Slovenian notice Spanish notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 107
lokala kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du köpte produkten för att få mer information om var du kan lämna ditt avfall för återvinning. 8-Gb SAN Switch Hardware Reference Guide 107 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 108
108 Regulatory compliance and safety - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 109
This type of damage may reduce the life expectancy of the device. To prevent HP authorized reseller install the part. NOTE: For more information on static electricity, or for assistance with product installation, contact your HP authorized reseller. 8-Gb SAN Switch Hardware Reference Guide - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 110
110 Electrostatic discharge - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 111
technology. Access Gateway. A software-enable feature that allows B-series Blade switches to function as port aggregators. Advanced Performance Monitor Application-Specific Integrated Circuit. B-series Fibre Channel switches and FICON directors manufactured for HP by Brocade Communications Systems - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 112
storage solution for the high-end enterprise class marketplace. Each EVA storage system consists of a pair of HSV virtualizing storage controllers and the disk drives they manage. fabric failover FC FCC FCIP FCoE A network of one or more Fibre Channel switches that transmit data between any - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 113
Channel routing. Fibre Channel switch. A serial data transport infrastructure and protocol used to implement SANs. See also http://www.fibrechannel.org/ and http://www.t11.org/. Fibre connectivity. Hardware that connects the mainframe to the CU. Fiber optic. Field-programmable gate array. Fabric - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 114
area such as a town, city, or suburb. Management Information Base (B-series). Million instructions per second. Multi-protocol Router. Multipath I/O (Microsoft software). Fibre Channel switches manufactured for HP by McDATA Corporation. Network address translation. N_Port ID Virtualization. An - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 115
about supported HP StorageWorks product configurations (http://www.hp.com/storage/spock). An HP Passport account is required for access. Short Reach. Selective Storage Presentation. A feature used to restrict access to a Fibre Channel LUN. Straight-tip connector. SAN Virtualization Services Platform - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 116
name. A unique identifier assigned to a Fibre Channel device. Worldwide port name. Synonymous with pWWN. Xcelerated Controller Software. The software that runs in the HSV controller-based Enterprise Virtual Array XL model storage systems. An HP StorageWorks product consisting of two or more XP disk - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 117
installing and configuring, 31 ISL trunking groups, 26 LEDs, 56 maintaining, 72 management features, 80 managing, 53 powering off, 45 powering on, 44 software options, 28 8/24 SAN switch, 12 activating additional ports, 13 features, 12 FRUs, 73 LEDs, 56 nonport side, 13 port side, 13 8/40 SAN switch - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 118
Network switch, 74 installing, 73 SAN encryption switch, 76 G grounding methods, 109 H HBAs, supported, 92 help obtaining, 93 HP technical support, 93 HP StorageWorks SAN switches 1606 Extension SAN Switch, 12 8/24, 11 8/40, 11 8/40 power pack+, 11 8/8 base, 11 8/8 full fabric, 11 8/80, 11 8/80 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 119
rack mount kit, 35 installation considerations, 32 installing FRUs, 73 IP address, setting, 46 ipaddrshow command, 47 ISL trunking groups, 26 L LEDs 1606 Extension SAN switch, 67 8/24 SAN switch, 56 8/40 SAN Switch, 57 8/8 SAN switch, 56 8/80 SAN switch, 58 Encryption SAN switch, 62 fan assembly, 75 - HP StorageWorks 1606 | HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 120
technical specifications, 83 technical support HP, 93 service locator website, 94 Telnet session opening, 47 text symbols, 95 time zones correcting, 49 setting, 49 W warning rack stability, 94 websites customer self repair, 96 HP , HP Subscriber's Choice for Business, 93 product manuals, 93 weight
HP StorageWorks
8-Gb SAN Switch Hardware Reference Guide
Abstract
This document provides information on installing, configuring, and maintaining the 8-Gb SAN family of HP
StorageWorks Fibre Channel switches. This document is intended for system administrators and technicians with
knowledge of SANs and HP StorageWorks Fibre Channel switches.
Part number: 5697-0291
Fifth edition: March 2010