HP StorageWorks 1606 HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 41

This also applies to the Encryption SAN Switch, FCoE Converged Network Switch,

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

7. Secure the two inner rails (one on each side) to the device, using the appropriate number of screws (see Table 6). For example, Figure 19 shows an inner rail attached to the MP Router with three screws, using the two rail screw holes marked R and one marked 16. Attaching both rails requires six screws. This figure also applies to the Encryption SAN Switch, FCoE Converged Network Switch, and 1606 Extension SAN Switch. Figure 20 shows an inner rail attached to the 4/64 SAN Switch with five screws, using the rail screw holes marked 16. Attaching both rails requires ten screws. This figure also applies to the 8/8, 8/24, 8/40, and 8/80 SAN Switches. Figure 19 Securing the inner rails to an MP Router . Figure 20 Securing the inner rails to the 4/64 SAN Switch . NOTE: For factory integration only, tighten the #8-32 x 5/16-inch Phillips panhead SEMS screws and torque between 6 and 8 inch-pounds. 8-Gb SAN Switch Hardware Reference Guide 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
7.
Secure the two inner rails (one on each side) to the device, using the appropriate number of
screws (see
Table 6
).
For example,
Figure 19
shows an inner rail attached to the MP Router with three screws, using
the two rail screw holes marked
R
and one marked
16
. Attaching both rails requires six screws.
This figure also applies to the Encryption SAN Switch, FCoE Converged Network Switch, and
1606 Extension SAN Switch.
Figure 20
shows an inner rail attached to the 4/64 SAN Switch with five screws, using the rail
screw holes marked
16
. Attaching both rails requires ten screws. This figure also applies to the
8/8, 8/24, 8/40, and 8/80 SAN Switches.
Figure 19 Securing the inner rails to an MP Router
.
Figure 20 Securing the inner rails to the 4/64 SAN Switch
.
NOTE:
For factory integration
only
, tighten the #8-32 x 5/16-inch Phillips panhead SEMS screws
and torque between 6 and 8 inch-pounds.
8-Gb SAN Switch Hardware Reference Guide
41