HP StorageWorks 1606 HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 75

Fan assembly LEDs, Replacing the 8/40 SAN Switch power supply and fan assembly

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Fan assembly LEDs Table 15 describes the fan status LED colors, behaviors, and actions required, if any. Table 15 Fan status LED behavior, description, and required actions LED color and behavi- Description or Action required No light Fan assembly is not receiving power. Verify that the fan FRU is seated correctly. Steady green Fan assembly is operating normally. No action required. Steady amber (for more than five seconds) Fan fault for one of the following reasons: • One or more of the fans in the fan assembly has failed. • The fan FRU was disabled by the user. Verify that the fan FRU is enabled. If the fan FRU is enabled and the FRU is faulty it should be replaced. Replacing the 8/40 SAN Switch power supply and fan assembly CAUTION: Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications. There are no user-serviceable parts inside the power supply and fan assembly. Because the cooling system relies on pressurized air, do not leave any of the fan assembly slots empty longer than two minutes while the switch is operating. If a fan assembly fails, leave it in the switch until it can be replaced. Maintain all fan assemblies in operational condition to provide redundancy. Replacing the power supply and fan assembly unit takes approximately two minutes. You will need: • New power supply and fan assembly FRU (one unit) • Phillips-head screwdriver #1 To replace the power supply and fan assembly unit: 1. Use a Phillips-head screwdriver to unscrew the captive screw on the power supply fan assembly you are replacing. 2. Remove the power supply fan assembly you are replacing from the chassis by pulling the handle out and away from the chassis. 3. Install the new power supply fan assembly unit in the chassis: a. Orient the new fan assembly with the captive screw on the right. b. Gently push the power supply fan assembly into the chassis until it is firmly seated. CAUTION: Do not force the installation. If the power supply fan assembly does not slide in easily, ensure that it is correctly oriented before continuing. c. Secure the fan assembly to the chassis by screwing in the captive screw. 8-Gb SAN Switch Hardware Reference Guide 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Fan assembly LEDs
Table 15
describes the fan status LED colors, behaviors, and actions required, if any.
Table 15 Fan status LED behavior, description, and required actions
Action required
Description
LED color and behavi-
or
Verify that the fan FRU is seated correctly.
Fan assembly is not receiving power.
No light
No action required.
Fan assembly is operating normally.
Steady green
Verify that the fan FRU is enabled. If the
fan FRU is enabled and the FRU is faulty
it should be replaced.
Fan fault for one of the following
reasons:
•
One or more of the fans in the fan
assembly has failed.
•
The fan FRU was disabled by the
user.
Steady amber (for more
than five seconds)
Replacing the 8/40 SAN Switch power supply and fan assembly
CAUTION:
Disassembling any part of the power supply and fan assembly voids the warranty and regulatory
certifications. There are no user-serviceable parts inside the power supply and fan assembly. Because
the cooling system relies on pressurized air, do not leave any of the fan assembly slots empty longer
than two minutes while the switch is operating. If a fan assembly fails, leave it in the switch until it
can be replaced. Maintain all fan assemblies in operational condition to provide redundancy.
Replacing the power supply and fan assembly unit takes approximately two minutes. You will need:
•
New power supply and fan assembly FRU (one unit)
•
Phillips-head screwdriver #1
To replace the power supply and fan assembly unit:
1.
Use a Phillips-head screwdriver to unscrew the captive screw on the power supply fan assembly
you are replacing.
2.
Remove the power supply fan assembly you are replacing from the chassis by pulling the handle
out and away from the chassis.
3.
Install the new power supply fan assembly unit in the chassis:
a.
Orient the new fan assembly with the captive screw on the right.
b.
Gently push the power supply fan assembly into the chassis until it is firmly seated.
CAUTION:
Do not force the installation. If the power supply fan assembly does not slide in easily,
ensure that it is correctly oriented before continuing.
c.
Secure the fan assembly to the chassis by screwing in the captive screw.
8-Gb SAN Switch Hardware Reference Guide
75