HP StorageWorks 1606 HP StorageWorks 8GB SAN Switch hardware reference guide ( - Page 43

Securing the device to the outer rails

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Securing the device to the outer rails To secure the device to the outer rails: 1. Insert the switch with the attached inner rails into the outer rails. NOTE: This step applies to installing a device in HP 9000 Series, HP 10000 Series, or HP System/e racks. 2. Insert the device into the rack, and install one #10-32 x 1/2-inch Phillips panhead screw with captive star lock washer. Repeat for the remaining side. (See Figure 22 and Figure 23.) Figure 22 Securing the switch (HP 9000 Series or HP 10000 Series racks) . Figure 23 Securing the device in an HP System/e Rack . 3. Tighten the hex nuts installed in step 4 of Installing the HP SAN Switch Rack Mount Kit in your HP custom rack, page 36. (See Figure 16, page 39.) This completes the rack mount procedure. 8-Gb SAN Switch Hardware Reference Guide 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Securing the device to the outer rails
To secure the device to the outer rails:
1.
Insert the switch with the attached inner rails into the outer rails.
NOTE:
This step applies to installing a device in HP 9000 Series, HP 10000 Series, or HP System/e
racks.
2.
Insert the device into the rack, and install one #10-32 x 1/2-inch Phillips panhead screw with
captive star lock washer. Repeat for the remaining side. (See
Figure 22
and
Figure 23
.)
Figure 22 Securing the switch (HP 9000 Series or HP 10000 Series racks)
.
Figure 23 Securing the device in an HP System/e Rack
.
3.
Tighten the hex nuts installed in step 4 of
Installing the HP SAN Switch Rack Mount Kit in your
HP custom rack
, page 36. (See
Figure 16
, page 39.)
This completes the rack mount procedure.
8-Gb SAN Switch Hardware Reference Guide
43