Lexmark T430 Service Manual - Page 169
Printhead assembly, adjustment
 |
View all Lexmark T430 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 169 highlights
4048-1xx 4. Lift the rear part of the top cover to clear the output tray full flags. You do not have to disconnect the top cover from the left and right guides to access the printhead. 5. Use a sharp pencil or other tool to mark the position of the printhead on the frame for re-alignment at installation. 6. Remove the three screws holding the printhead (C). 7. Remove the printhead. 8. Disconnect the printhead cables (D). Note: When reinstalling the printhead, check the alignment of the printhead to the frame and perform the "Printhead assembly adjustment" on page 4-2 before reinstalling the top cover. Repair information 4-47
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164 -
165 -
166 -
167 -
168 -
169 -
170 -
171 -
172 -
173 -
174 -
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
 |
 |
Repair information
4-47
4048-1
xx
4.
Lift the rear part of the top cover to clear the output tray full
flags.
You do not have to disconnect the top cover from the left and
right guides to access the printhead.
5.
Use a sharp pencil or other tool to mark the position of the
printhead on the frame for re-alignment at installation.
6.
Remove the three screws holding the printhead (C).
7.
Remove the printhead.
8.
Disconnect the printhead cables (D).
Note:
When reinstalling the printhead, check the alignment of the
printhead to the frame and perform the
“Printhead assembly
adjustment” on page 4-2
before reinstalling the top cover.