Ricoh Aficio MP 6001 SP Operating Instructions - Page 89

In [System Settings], under [Interface

Get Ricoh Aficio MP 6001 SP PDF manuals and user guides View all Ricoh Aficio MP 6001 SP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

When You Cannot Print When You Cannot Print This section describes what to do if printing does not start even after performing [Print]. Problem Printing does not start. Printing does not start. Printing does not start. Printing does not start. Printing does not start. Printing does not start. Printing does not start. Cause Solution The power is off. Check the cable is securely plugged into the power outlet and the machine. Turn on the main power switch. The machine is set to Press [ Online]. "Offline". The cause is displayed on the Check the error message or warning 4 display of the control panel. status on the display panel and take the required action. The interface cable is not connected correctly. Connect the interface cable securely. If it has a fastener, fasten that securely as well. See "Connecting to the Interfaces", Network and System Settings Guide . The correct interface cable is not being used. The type of interface cable you should use depends on the computer. Be sure to use the correct one. If the cable is damaged or worn, replace it. See "Connecting to the Interfaces", Network and System Settings Guide . The interface cable was connected after the machine was switched on. Connect the interface cable before turning on the machine. If the machine is using wireless LAN, failure to print might result from a weak wireless signal. In [System Settings], under [Interface Settings], select [Wireless LAN], and then press [Wireless LAN Signal] to check signal status. If signal quality is poor, move the machine to a location where radio waves can pass or remove objects that might cause interference. (You can check signal status only when using wireless LAN in the infrastructure mode.) 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
When You Cannot Print
This section describes what to do if printing does not start even after performing [Print].
Problem
Cause
Solution
Printing does not start.
The power is off.
Check the cable is securely plugged into
the power outlet and the machine. Turn
on the main power switch.
Printing does not start.
The machine is set to
"Offline".
Press [
Online].
Printing does not start.
The cause is displayed on the
display of the control panel.
Check the error message or warning
status on the display panel and take the
required action.
Printing does not start.
The interface cable is not
connected correctly.
Connect the interface cable securely. If
it has a fastener, fasten that securely as
well. See "Connecting to the Interfaces",
Network and System Settings Guide
.
Printing does not start.
The correct interface cable is
not being used.
The type of interface cable you should
use depends on the computer. Be sure to
use the correct one. If the cable is
damaged or worn, replace it. See
"Connecting to the Interfaces", Network
and System Settings Guide
.
Printing does not start.
The interface cable was
connected after the machine
was switched on.
Connect the interface cable before
turning on the machine.
Printing does not start.
If the machine is using
wireless LAN, failure to print
might result from a weak
wireless signal.
In [System Settings], under [Interface
Settings], select [Wireless LAN], and
then press [Wireless LAN Signal] to
check signal status. If signal quality is
poor, move the machine to a location
where radio waves can pass or remove
objects that might cause interference.
(You can check signal status only when
using wireless LAN in the infrastructure
mode.)
When You Cannot Print
87
4