Dell PowerEdge C6220 II Hardware Owners Manual - Page 321
System Configuration Jumper Settings on the C6220 System Board
 |
View all Dell PowerEdge C6220 II manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 321 highlights
System Configuration Jumper Settings on the C6220 System Board The function of system configuration jumper installed on each C6220 system board is shown below: Figure 5-19. System Configuration Jumpers on the C6220 System Board Table 5-2. System Configuration Jumper on the C6220 System Board Jumper Function Off Service Mode *Disable NVRAM Clear *Disable BIOS Recovery *Disable ME Firmware Recovery *Disable MEDBG1 *Disable Power Button Pass *Disable Jumper Function Pin1-2 PWRD_EN *Enable On Enable Enable Enable Enable Enable Enable Pin2-3 Disable NOTE: The * in the table of system configuration jumper describes the default status and the default state is not active state. Jumpers and Connectors | 321
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316 -
317 -
318 -
319 -
320 -
321 -
322 -
323 -
324 -
325 -
326 -
327
-
328
-
329
 |
 |
Jumpers and Connectors |
321
System Configuration Jumper Settings on the C6220 System Board
The function of system configuration jumper installed on each C6220
system board is shown below:
Figure 5-19.
System Configuration Jumpers on the C6220 System Board
Table 5-2.
System Configuration Jumper on the C6220 System Board
Jumper
Function
Off
On
Service Mode
*Disable
Enable
NVRAM Clear
*Disable
Enable
BIOS Recovery
*Disable
Enable
ME Firmware Recovery
*Disable
Enable
MEDBG1
*Disable
Enable
Power Button Pass
*Disable
Enable
Jumper
Function
Pin1-2
Pin2-3
PWRD_EN
*Enable
Disable
NOTE:
The
*
in the table of system configuration jumper describes the default
status and the default state is not active state.