Dell PowerEdge M520 Dell PowerConnect M6220/M6348/M8024 Switches Configuration - Page 123

Example 7: Modify the Default Captive Portal Configuration Change Verification Method to Local

Get Dell PowerEdge M520 PDF manuals and user guides View all Dell PowerEdge M520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 123 highlights

Example 5: Show Captive Portal To show the status of Captive Portal, use the following command: console#show captive-portal Administrative Mode Enabled Operational Status Enabled Disable Reason Administrator Disabled Captive Portal IP Address 1.2.3.4 Example 6: Show Captive Portal Instances To show the status of all Captive Portal instances in the system, use the following command: console#show captive-portal status Additional HTTP Port 81 Additional HTTP Secure Port 0 Peer Switch Statistics Reporting Interval...... 300 Authentication Timeout 600 Supported Captive Portals 10 Configured Captive Portals 2 Active Captive Portals 1 System Supported Users 1024 Local Supported Users 128 Authenticated Users 0 Example 7: Modify the Default Captive Portal Configuration (Change Verification Method to Local) To change the verification method to local, use the following command: console(config-CP 1)#verification local To view the configuration change, use the following command: console#show captive-portal configuration 1 status CP ID 1 CP Name Default CP Mode Enable Protocol Mode HTTP Verification Mode Local Group ID 1 Group Name Default User Logout Mode Enable URL Redirect Mode Disable Session Timeout 0 Idle Timeout 0 Max Bandwidth Up (bytes/sec 0 Max Bandwidth Down (bytes/sec 0 Device Security 123

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Device Security
123
Example 5: Show Captive Portal
To show the status of Captive Portal, use the following command:
console#show captive-portal
Administrative Mode
.......................
Enabled
Operational Status
........................
Enabled
Disable Reason
............................
Administrator Disabled
Captive Portal IP Address
.................
1.2.3.4
Example 6: Show Captive Portal Instances
To show the status of all Captive Portal instances in the system, use the following command:
console#show captive-portal status
Additional HTTP Port
...........................
81
Additional HTTP Secure Port
....................
0
Peer Switch Statistics Reporting Interval
......
300
Authentication Timeout
.........................
600
Supported Captive Portals
......................
10
Configured Captive Portals
.....................
2
Active Captive Portals
.........................
1
System Supported Users
.........................
1024
Local Supported Users
..........................
128
Authenticated Users
............................
0
Example 7: Modify the Default Captive Portal Configuration (Change Verification Method to Local)
To change the verification method to local, use the following command:
console(config-CP 1)#verification local
To view the configuration change, use the following command:
console#show captive-portal configuration 1 status
CP ID
..........................................
1
CP Name
........................................
Default
CP Mode
........................................
Enable
Protocol Mode
..................................
HTTP
Verification Mode
..............................
Local
Group ID
.......................................
1
Group Name
.....................................
Default
User Logout Mode
...............................
Enable
URL Redirect Mode
..............................
Disable
Session Timeout
................................
0
Idle Timeout
...................................
0
Max Bandwidth Up (bytes/sec)
...................
0
Max Bandwidth Down (bytes/sec)
.................
0