Dell PowerEdge M520 Dell PowerConnect M6220/M6348/M8024 Switches Configuration - Page 27

Example #1: Create Two VLANs, Example #2: Assign Ports to VLAN2, accepted on ports 1/g19 and 1/g20.

Get Dell PowerEdge M520 PDF manuals and user guides View all Dell PowerEdge M520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Example #1: Create Two VLANs Use the following commands to create two VLANs and to assign the VLAN IDs while leaving the names blank. console(config)#vlan database console(config-vlan)#vlan 2 console(config-vlan)#vlan 3 console(config-vlan)#exit Example #2: Assign Ports to VLAN2 This sequence shows how to assign ports to VLAN2, specify that frames will always be transmitted tagged from all member ports, and that untagged frames will be rejected on receipt. console(config)#interface ethernet 1/g17 console(config-if-1/g17)#switchport mode general console(config-if-1/g17)#switchport general allowed vlan add 2 tagged console(config-if-1/g17)#switchport general acceptable-frame-type tagged-only console(config-if-1/g17)#exit console(config)#interface ethernet 1/g18 console(config-if-1/g18)#switchport mode general console(config-if-1/g18)#switchport general allowed vlan add 2 tagged console(config-if-1/g18)#switchport general acceptable-frame-type tagged-only console(config-if-1/g18)#exit Example #3: Assign Ports to VLAN3 This example shows how to assign the ports that will belong to VLAN 3. Untagged frames will be accepted on ports 1/g19 and 1/g20. Note that port 1/g18 belongs to both VLANs and that port 1/g17 does not belong to VLAN 3. console(config)#interface ethernet 1/g18 cconsole(config-if-1/g18)#switchport general allowed vlan add 3 console(config-if-1/g18)#exit console(config)#interface ethernet 1/g19 console(config-if-1/g19)#switchport general allowed vlan add 3 console(config-if-1/g19)#exit console(config)#interface ethernet 1/g20 console(config-if-1/g20)#switchport general allowed vlan add 3 Switching Configuration 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Switching Configuration
27
Example #1: Create Two VLANs
Use the following commands to create two VLANs and to assign the VLAN IDs while leaving the names
blank.
console(config)#vlan database
console(config-vlan)#vlan 2
console(config-vlan)#vlan 3
console(config-vlan)#exit
Example #2: Assign Ports to VLAN2
This sequence shows how to assign ports to VLAN2, specify that frames will always be transmitted
tagged from all member ports, and that untagged frames will be rejected on receipt.
console(config)#interface ethernet 1/g17
console(config-if-1/g17)#switchport mode general
console(config-if-1/g17)#switchport general allowed vlan add 2 tagged
console(config-if-1/g17)#
switchport general acceptable-frame-type tagged-only
console(config-if-1/g17)#exit
console(config)#interface ethernet 1/g18
console(config-if-1/g18)#switchport mode general
console(config-if-1/g18)#switchport general allowed vlan add 2 tagged
console(config-if-1/g18)#
switchport general acceptable-frame-type tagged-only
console(config-if-1/g18)#exit
Example #3: Assign Ports to VLAN3
This example shows how to assign the ports that will belong to VLAN 3. Untagged frames will be
accepted on ports 1/g19 and 1/g20.
Note that port 1/g18 belongs to both VLANs and that port 1/g17 does not belong to VLAN 3.
console(config)#interface ethernet 1/g18
cconsole(config-if-1/g18)#switchport general allowed vlan add 3
console(config-if-1/g18)#exit
console(config)#interface ethernet 1/g19
console(config-if-1/g19)#switchport general allowed vlan add 3
console(config-if-1/g19)#exit
console(config)#interface ethernet 1/g20
console(config-if-1/g20)#switchport general allowed vlan add 3