Dell PowerEdge M520 Dell PowerConnect M6220/M6348/M8024 Switches Configuration - Page 73

Using the Web Interface to Con VRRP, Proxy Address Resolution Protocol (ARP), Overview

Get Dell PowerEdge M520 PDF manuals and user guides View all Dell PowerEdge M520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Enable VRRP on the port. console(config-if-vlan60)#ip vrrp 20 mode console(config-if-vlan60)#exit Using the Web Interface to Configure VRRP Use the following screens to perform the same configuration using the Graphical User Interface: • Routing > IP > Configuration. To enable routing for the switch. • Routing > IP > Interface Configuration. To enable routing for the VLAN interfaces and configure their IP addresses and subnet masks. • Routing > VRRP > VRRP Configuration. To enable VRRP for the switch • Routing > VRRP > Virtual Router Configuration. To configure the interface for VRRP. Proxy Address Resolution Protocol (ARP) This section describes the Proxy Address Resolution Protocol (ARP) feature. Overview • Proxy ARP allows a router to answer ARP requests where the target IP address is not the router itself but a destination that the router can reach. • If a host does not know the default gateway, proxy ARP can learn the first hop. • Machines in one physical network appear to be part of another logical network. • Without proxy ARP, a router responds to an ARP request only if the target IP address is an address configured on the interface where the ARP request arrived. CLI Examples The following are examples of the commands used in the proxy ARP feature. Example #1: Enabling Proxy ARP To enable IP Proxy ARP: console#config console(config)#interface vlan 10 console(config-if-vlan10)#routing console(config-if-vlan10)#ip proxy-arp console(config-if-vlan10)#exit Example #2 Viewing the Interface Information console#show ip interface vlan 50 Routing Configuration 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Routing Configuration
73
Enable VRRP on the port.
console(config-if-vlan60)#ip vrrp 20 mode
console(config-if-vlan60)#exit
Using the Web Interface to Configure VRRP
Use the following screens to perform the same configuration using the Graphical User Interface:
•
Routing > IP > Configuration.
To enable routing for the switch.
•
Routing > IP > Interface Configuration.
To enable routing for the VLAN interfaces and configure
their IP addresses and subnet masks.
•
Routing > VRRP > VRRP Configuration.
To enable VRRP for the switch
•
Routing > VRRP > Virtual Router Configuration.
To configure the interface for VRRP.
Proxy Address Resolution Protocol (ARP)
This section describes the Proxy Address Resolution Protocol (ARP) feature.
Overview
•
Proxy ARP allows a router to answer ARP requests where the target IP address is not the router itself
but a destination that the router can reach.
•
If a host does not know the default gateway, proxy ARP can learn the first hop.
•
Machines in one physical network appear to be part of another logical network.
•
Without proxy ARP, a router responds to an ARP request only if the target IP address is an address
configured on the interface where the ARP request arrived.
CLI Examples
The following are examples of the commands used in the proxy ARP feature.
Example #1: Enabling Proxy ARP
To enable IP Proxy ARP:
console#config
console(config)#interface vlan 10
console(config-if-vlan10)#routing
console(config-if-vlan10)#ip proxy-arp
console(config-if-vlan10)#exit
Example #2 Viewing the Interface Information
console#show ip interface vlan 50