Dell PowerEdge M520 Dell PowerConnect M6220/M6348/M8024 Switches Configuration - Page 91

and remote packets.

Get Dell PowerEdge M520 PDF manuals and user guides View all Dell PowerEdge M520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Loopbacks are typically used for device management purposes. A client can use the loopback interface to communicate with the router through various services such as telnet and SSH. The address on a loopback behaves identically to any of the local addresses of the router in terms of the processing of incoming packets. This interface provides the source address for sent packets and can receive both local and remote packets. NOTE: The following example uses the CLI to configure a loopback interface. You can also use the Web interface. Click Routing > Loopbacks in the navigation tree. You can create a loopback interface in the Global Config mode by assigning it a unique ID from 0 to 7: console#configure console(config)#interface loopback 0 Next, you assign an IPv4 or IPv6 address to the interface: console(config-if-loopback0)#ip address 192.168.1.2 255.255.255.255 console(config-if-loopback0)#exit console(config)#exit You can view the interface configuration from the Privileged Exec mode: console#show ip interface loopback 0 Primary IP Address 192.168.2.2/255.255.255.255 Routing Mode Enable Administrative Mode Enable Forward Net Directed Broadcasts Disable Proxy ARP Enable Local Proxy ARP Disable Active State Active Link Speed Data Rate Inactive MAC Address 00FF.F2A3.8888 Encapsulation Type IP MTU 1500 Bandwidth 100000 kbps Destination Unreachables Enabled ICMP Redirects Enabled To delete a loopback interface, enter the following command from the Global Config mode: console(config)#no interface loopback 0 console(config)# Routing Configuration 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Routing Configuration
91
Loopbacks are typically used for device management purposes. A client can use the loopback interface to
communicate with the router through various services such as telnet and SSH. The address on a
loopback behaves identically to any of the local addresses of the router in terms of the processing of
incoming packets. This interface provides the source address for sent packets and can receive both local
and remote packets.
NOTE:
The following example uses the CLI to configure a loopback interface. You can also use the Web interface.
Click
Routing > Loopbacks
in the navigation tree.
You can create a loopback interface in the Global Config mode by assigning it a unique ID from 0 to 7:
console#configure
console(config)#interface loopback 0
Next, you assign an IPv4 or IPv6 address to the interface:
console(config-if-loopback0)#ip address 192.168.1.2 255.255.255.255
console(config-if-loopback0)#exit
console(config)#exit
You can view the interface configuration from the Privileged Exec mode:
console#show ip interface loopback 0
Primary IP Address
.............................
192.168.2.2/255.255.255.255
Routing Mode
...................................
Enable
Administrative Mode
............................
Enable
Forward Net Directed Broadcasts
................
Disable
Proxy ARP
......................................
Enable
Local Proxy ARP
................................
Disable
Active State
...................................
Active
Link Speed Data Rate
...........................
Inactive
MAC Address
....................................
00FF.F2A3.8888
Encapsulation Type
.............................
--------
IP MTU
.........................................
1500
Bandwidth
......................................
100000 kbps
Destination Unreachables
.......................
Enabled
ICMP Redirects
.................................
Enabled
To delete a loopback interface, enter the following command from the Global Config mode:
console(config)#no interface loopback 0
console(config)#