Dell PowerEdge M520 Dell PowerConnect M6220/M6348/M8024 Switches Configuration - Page 28

Example #4: Assign VLAN3 as the Default VLAN, Example #5: Assign IP Addresses to VLAN 2

Page 28 highlights

Example #4: Assign VLAN3 as the Default VLAN This example shows how to assign VLAN 3 as the default VLAN for port 1/g18. console(config)#interface ethernet 1/g18 console(config-if-1/g18)#switchport general pvid 3 Example #5: Assign IP Addresses to VLAN 2 In order for the VLAN to function as a routing interface, you must enable routing on the VLAN and on the switch. Routing is only permitted on VLAN interfaces. Routing on physical interfaces is not supported. console#configure console(config)#interface vlan 2 console(config-if-vlan2)#ip address 192.168.10.33 255.255.255.0 console(config-if-vlan2)#routing console(config-if-vlan2)#exit console(config)#ip routing Example #6: View Information About VLAN 2 console#show ip interface vlan 2 Primary IP Address 192.168.10.33/255.255.255.0 Routing Mode Enable Administrative Mode Enable Forward Net Directed Broadcasts........... Disable Proxy ARP Enable Local Proxy ARP Disable Active State Inactive MAC Address 00FF.F2A3.888A Encapsulation Type Ethernet IP MTU 1500 Bandwidth 10000 kbps Destination Unreachables Enabled ICMP Redirects Enabled 28 Switching Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158

28
Switching Configuration
Example #4: Assign VLAN3 as the Default VLAN
This example shows how to assign VLAN 3 as the default VLAN for port 1/g18.
console(config)#interface ethernet 1/g18
console(config-if-1/g18)#switchport general pvid 3
Example #5: Assign IP Addresses to VLAN 2
In order for the VLAN to function as a routing interface, you must enable routing on the VLAN and on
the switch. Routing is only permitted on VLAN interfaces. Routing on physical interfaces is not
supported.
console#configure
console(config)#interface vlan 2
console(config-if-vlan2)#ip address 192.168.10.33 255.255.255.0
console(config-if-vlan2)#routing
console(config-if-vlan2)#exit
console(config)#ip routing
Example #6: View Information About VLAN 2
console#show ip interface vlan 2
Primary IP Address
........................
192.168.10.33/255.255.255.0
Routing Mode
..............................
Enable
Administrative Mode
.......................
Enable
Forward Net Directed Broadcasts
...........
Disable
Proxy ARP
.................................
Enable
Local Proxy ARP
...........................
Disable
Active State
..............................
Inactive
MAC Address
...............................
00FF.F2A3.888A
Encapsulation Type
........................
Ethernet
IP MTU
....................................
1500
Bandwidth
.................................
10000 kbps
Destination Unreachables
..................
Enabled
ICMP Redirects
............................
Enabled