HP A7533A HP StorageWorks Fabric OS 6.1.1 administrator guide (5697-0235, Dece - Page 403
stand-alone 400 Multi-protocol Router.
![]() |
UPC - 829160830858
View all HP A7533A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 403 highlights
where: slot ge0|ge1 src_ipaddr mtu_size The number of a slot in a 4/256 SAN Director or DC Director chassis that contains an FR4-18i blade. This parameter does not apply to the stand-alone 400 Multi-protocol Router. The Ethernet port used by the tunnel (ge0 or ge1). Specify source IP address in either IPv6 or IPv4 format: src_IPv6_addr/[prefix_len] Specifies the source IPv6 address of the virtual port if IPv6 is used. The address must be an IPv6 global, unicast address. As an option, specify the prefix length. This is used for IPv6 addresses instead of a netmask. If prefix_len is not specified, the prefix length learned from the Neighbor Discovery protocol will be used. src_PIv4_addr netmask Specifies the source IPv4 address of the virtual port, if IPv4 is used. If an IPv4 address is used, the subnet mask must be specified as well (in a.b.c.d format). The maximum transmission unit size. The range allowed is 1500 to 2284 B. The default value is 1260 B, which is the normal value in an Ethernet network. Some networks support jumbo packets (packets larger than 1500 B). If the network you are using supports jumbo packets, a value of 2284 can improve performance. By default, the virtual ports automatically become VE_Ports. 2. Define IP routes on a GbE port. After defining the IP interface of the remote switch, you can define destination routes on an interface. You can specify a maximum of 32 routes per GbE port. The command syntax is as follows. portcfg iproute [slot/]ge0|ge1 create idest_paddr [gateway_router] metric where: slot ge0|ge1 dest_ipaddr is the number of a slot in a 4/256 SAN Director or DC Director chassis that contains an FR4-18i blade. This parameter does not apply to the stand-alone 400 Multi-protocol Router. is the Ethernet port used by the tunnel (ge0 or ge1). specifies the source IP address in either IPv6 or IPv4 format: dest_IPv6_addr/[prefix_len] specifies the destination IPv6 address of the virtual port, if IPv6 is used. The address must be an IPv6 global, unicast address. As an option, specify the prefix length. This is used for IPv6 addresses instead of a netmask. If prefix_len is not specified, the prefix length learned from the Neighbor Discovery protocol is used. gateway_router dest_IPv4_addr netmask specifies the destination IPv4 address of the virtual port, if IPv4 is used. If an IPv4 address is used, the subnet mask must be specified as well; use a.b.c.d format. specifies the IP address of an IP router that can route packets to the destination virtual port IP address. The gateway address must be on the same IP subnet as one of the port IP addresses. This operand is optional with IPv6 addresses. If not specified, the gateway_router learned from the Neighbor Discovery protocol is used. metric specifies the link metric associated with the route. Valid values are 0-255. The default value is 0. A low value encourages the use of the route; a high value discourages the use of a route. The following example shows two routes being added to an interface: switch:admin06> portcfg iproute 8/ge0 create 192.168.11.0 255.255.255.0 192.168.100.1 1 switch:admin06> portcfg iproute 8/ge0 create 192.168.12.0 255.255.255.0 192.168.100.1 1 Fabric OS 6.1.x administrator guide 403
![](/manual_guide/products/hewlettpackard-ae370a-hp-storageworks-fabric-os-611-administrator-guide-56970235-2009-a28315e/403.png)