HP LH4r HP Netserver LH 6000 Installation Guide - Page 109

Introduction

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

10 Configuring the HP NetServer Introduction This chapter describes: l Configuring the HP NetServer l Installing the Network Operating System (NOS) NOTE The HP NetServer ships with NetRAID as the default. If you plan to configure mass storage as LVD SCSI, use Setup Utility to change the Configuration/Embedded LAN and SCSI Settings to Enable LVD SCSI prior to installing the NOS. Run the Setup utility to do the following: • For HP NetServer LH 6000/6000r, use the Setup utility to put SCSI channels A and B under control of the integrated HP NetRAID controller and to verify the boot device priority and the priority of various hard disk drive controllers within the boot device priority. Start Setup Utility 1. Turn on power to the HP NetServer and display monitor. If you receive an error message during the boot process, refer to Chapter 12, "Troubleshooting," or the online help. Some power-up (boot) messages are routine. 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
101
10
Configuring the HP NetServer
Introduction
This chapter describes:
Configuring the HP NetServer
Installing the Network Operating System (NOS)
NOTE
The HP NetServer ships with NetRAID as the default. If you
plan to configure mass storage as LVD SCSI, use Setup Utility
to change the Configuration/Embedded LAN and SCSI
Settings to Enable LVD SCSI prior to installing the NOS.
Run the Setup utility to do the following:
•
For HP NetServer LH 6000/6000r, use the Setup utility to put SCSI
channels A and B under control of the integrated HP NetRAID controller
and to verify the boot device priority and the priority of various hard disk
drive controllers within the boot device priority.
Start Setup Utility
1.
Turn on power to the HP NetServer and display monitor.
If you receive an error message during the boot process, refer to Chapter
12, "Troubleshooting," or the online help. Some power-up (boot) messages
are routine.