HP LH4r HP Netserver LH 6000 Installation Guide - Page 85

Upgrading the Firmware

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 7 Installing Additional Processors Table 7-1. Configuration Switches - CPU Speed Speed Switch 1 Switch 2 Switch 3 Switch 4 550 MHz ON OFF OFF OFF 600 MHz OFF ON ON ON 650 MHz OFF ON ON OFF 700 MHz OFF ON OFF ON 750 MHz OFF ON OFF OFF Table 7-2. Configuration Switches S5-S8 Switch Function Switch 5 Switch 6 Switch 7 Switch 8 Clear Configuration Clear Password Boot Block Not Used To Enable ON (normally OFF) ON (normally OFF) ON (normally OFF) N/A (normally OFF) NOTE Some processor speeds listed in Table 7-1 may not be supported. For the latest support information, visit the HP web site: http://www.hp.com/go/netserver Upgrading the Firmware Load the HP NetServer Navigator CD-ROM and then power on the LH 6000r and LH 6000. Follow instructions to ensure that the BIOS is up-to-date. NOTE You are not required to use the HP NetServer Navigator CD-ROM to reconfigure your system after installing the new processor. The NetServer detects the additional processors automatically. However, HP recommends using the HP NetServer Navigator CD-ROM that comes with the processor upgrade kit to ensure you have the latest drivers and information. 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 7
Installing Additional Processors
77
Table 7-1. Configuration Switches – CPU Speed
Speed
Switch 1
Switch 2
Switch 3
Switch 4
550 MHz
ON
OFF
OFF
OFF
600 MHz
OFF
ON
ON
ON
650 MHz
OFF
ON
ON
OFF
700 MHz
OFF
ON
OFF
ON
750 MHz
OFF
ON
OFF
OFF
Table 7-2. Configuration Switches S5-S8
Switch
Function
To Enable
Switch 5
Clear Configuration
ON (normally OFF)
Switch 6
Clear Password
ON (normally OFF)
Switch 7
Boot Block
ON (normally OFF)
Switch 8
Not Used
N/A (normally OFF)
NOTE
Some processor speeds listed in Table 7-1 may not be
supported. For the latest support information, visit the HP web
site:
Upgrading the Firmware
Load the
HP NetServer Navigator CD-ROM
and then power on the LH 6000r and
LH 6000. Follow instructions to ensure that the BIOS is up-to-date.
NOTE
You are not required to use the
HP NetServer Navigator
CD-ROM
to reconfigure your system after installing the new
processor. The NetServer detects the additional processors
automatically. However, HP recommends using the
HP
NetServer Navigator CD-ROM
that comes with the processor
upgrade kit to ensure you have the latest drivers and
information.