HP LH4r HP Netserver LH 6000 Installation Guide - Page 110

Press <F2> to enter SETUP

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 10 Configuring the HP NetServer NOTE The message "Configuration of NVRAM and drives mismatch" indicates that configuration information in the integrated HP NetRAID controller's NVRAM differs from configuration information in hard disk drives. Do the following to clear configuration information from integrated HP NetRAID NVRAM: 1. Press Ctrl+M to start the HP NetRAID Express Tools utility. 2. On the Tools Management Menu, choose Configure. 3. On the Configure menu, choose Clear Configuration. • If the question "Clear Configuration?" is displayed, answer Yes. Then press any key to continue, and go to Step 4 in this note. • If the message "No Existing Configuration to Clear" is displayed, press Esc to return to the Configuration menu, choose New Configuration, and answer Yes to the question "Proceed?". When the scan finishes, all drives are shown in the Ready state. Press Enter to end the array, and answer Yes to the question "Save Configuration?". When "Configuration is Saved" is displayed, press any key. 4. To exit HP NetRAID Express Tools, press ESC repeatedly until the Exit? box appears. Choose YES to exit. Then press Ctrl+Alt+Del to restart the NetServer. 2. As soon as you see the message Press to enter SETUP on the display monitor, press the F2 function key. NOTE If you wait too long to press the F2 function key, you may not be able to enter the Setup utility, even though the message "Press to enter SETUP" is still displayed. If this happens, restart the HP NetServer and press the F2 function key as soon as the message appears. 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 10
Configuring the HP NetServer
102
NOTE
The message "Configuration of NVRAM and drives mismatch"
indicates that configuration information in the integrated HP
NetRAID controller’s NVRAM differs from configuration
information in hard disk drives.
Do the following to clear configuration information from
integrated HP NetRAID NVRAM:
1. Press
Ctrl+M
to start the HP NetRAID Express Tools
utility.
2. On the Tools Management Menu, choose
Configure
.
3. On the Configure menu, choose
Clear Configuration
.
•
If the question "Clear Configuration?" is displayed, answer
Yes
. Then press any key to continue, and go to Step 4 in
this note.
•
If the message "No Existing Configuration to Clear" is
displayed, press Esc to return to the Configuration menu,
choose
New Configuration
, and answer
Yes
to the
question "Proceed?". When the scan finishes, all drives are
shown in the Ready state. Press
Enter
to end the array, and
answer
Yes
to the question "Save Configuration?". When
"Configuration is Saved" is displayed, press any key.
4.
To exit HP NetRAID Express Tools, press
ESC
repeatedly
until the Exit? box appears. Choose
YES
to exit. Then press
Ctrl+Alt+Del
to restart the NetServer.
2.
As soon as you see the message
Press <F2> to enter SETUP
on the display monitor, press the
F2
function key.
NOTE
If you wait too long to press the
F2
function key, you may not
be able to enter the Setup utility, even though the message
"Press <F2> to enter SETUP" is still displayed. If this happens,
restart the HP NetServer and press the
F2
function key as soon
as the message appears.